to a locking posi- |
| hinge and you will be able to adjust the | ||
tion. The unit will |
| Griddler™ Jr. more easily. |
| |
stay in this posi- |
| To insert cooking plates |
| |
tion until you close |
|
| ||
| Adjust the Griddler™ Jr. to the flat position | |||
the cover or con- |
| |||
| (see below) with the controls directly in front | |||
tinue to open it to |
| |||
| of you. Insert one plate at a time. Each plate | |||
the flat position. |
| |||
| is designed to fit in either the upper housing | |||
The cover will stay |
| |||
| or the lower housing of the Griddler™ Jr. The | |||
in the upright position until you lower the | word “lower” or “upper” |
| ||
handle for cooking. When this is done, the |
| |||
is embossed into each grill plate to let you | ||||
hinge will release itself so that the upper | ||||
know where to attach the plate. Pick up the | ||||
plate lies flat on the top of the food you are | ||||
lower grill plate with the cutouts for the | ||||
preparing. This allows you to cook your food | ||||
heating element facing down. |
| |||
evenly from both top and bottom. When you |
| |||
If you are facing the Griddler™ Jr. the drip | ||||
lift the handle to open the Griddler™ after | ||||
cooking the cover will remain in the flat | spouts should be at the forward corners of | |||
the plate. Locate the metal brackets at the | ||||
position, parallel with the lower plate. In | ||||
center of the housing. Tilt the back end of | ||||
order to lock the cover back into the upright | ||||
the plate and line up the cutouts at the back | ||||
position, you must close the Griddler™ Jr., | ||||
without any food in place, and open it again. | of the plate with the metal brackets. Slide | |||
the plate underneath the brackets and push | ||||
|
| |||
Flat Position – |
| down the front end of the plate. It will snap | ||
| into place. Turn the Griddler™ Jr. around and | |||
Upper plate/ |
| insert the matching grill plate into the upper | ||
cover is level |
| housing as you did with the first plate. | ||
with lower |
| To remove cooking plates |
| |
plate/base. The |
|
| ||
| Adjust Griddler™ Jr. to flat position. Locate | |||
upper and |
| |||
| the plate release buttons on one side of the | |||
lower plates |
| |||
| unit. Press firmly on button and the plate will | |||
line up to cre- |
| |||
| pop up slight- |
| ||
ate one large cooking surface. The Griddler™ | Upper plate | |||
Jr. is in this position when it is used as an | ly from the | |||
base. Grasp | release button | |||
open grill. |
| |||
| the plate with |
| ||
To adjust the Griddler™ Jr. to this position, |
| |||
two hands, | Lower plate | |||
locate the hinge release lever on the right | ||||
slide it out | release button | |||
arm. (see diagram below) |
| |||
| from under |
| ||
|
|
| ||
With your left | Hinge | the metal brackets, and lift it out of the | ||
hand on the | base. Press on the other plate release but- | |||
handle, use your | release | ton to remove the other cooking plate in the | ||
right hand to | lever | same manner. |
| |
|
| |||
slide the lever |
| To position drip cups |
| |
toward you. Push the handle back until the |
| |||
When using the Griddler™ Jr. as a contact | ||||
cover rests flat on the counter. The unit will | ||||
grill or panini press place the cup directly | ||||
stay in this position until you lift the handle | ||||
below the grease spout while cooking. | ||||
and cover to return it to the closed position. | ||||
Grease from the food will run off the plates | ||||
If the Griddler™ Jr. is already in the open | ||||
through the grease spout and into the drip | ||||
position and you wish to adjust it to the flat | ||||
cup. Grease should be safely disposed of | ||||
position, pull the handle slightly toward you | ||||
after cooking. The drip cups can be cleaned | ||||
and then lift the hinge release lever. Push | ||||
in the dishwasher. |
| |||
the handle back until the cover rests in the |
| |||
When using the Griddler™ Jr. as an open | ||||
flat position. Pulling the handle forward | ||||
grill, place the cups at either end of the unit | ||||
slightly before lifting the hinge release lever | ||||
directly below the grease spouts. | ||||
will take some of the pressure off of the | ||||
|
| |||
|
|
|