Channel Plus H612 manual Typical Installation

ChannelPlus Telephone Entry Module

IMPORTANT INSTRUCTIONS

When using your telephone equipment, basic precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following:

1.Read and understand all instructions

2.Do not use this product near water, for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool.

3.Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltages.

4.SAVE THESE INSTRUCTIONS

SAFETY INFORMATION:

a)Never install telephone wiring during a lighting storm.

b)Never install telephone jacks in wet locations.

c)Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface.

d)Use caution when installing or modifying telephone lines.

OpenHousetm modules attach from the top

1)Hook from the top

2)Swing into place

3)Push button to lock

1

3	Telephone Master Hub (4 lines x 6 phones)
	ChannelPlus model H616

2

The H612 Telephone Entry Module provides a superior method of telephone connection to your system. Each unit provides surge suppression for two lines and a master disconnect. Also,

							each line has an LED
			Telephone Entry Module (surge,disconnect)				status indicator to warn
				ChannelPlus model H612
	From NTE						you of a surge event.
	Line 2
1	6		Disconnect	Surge	Expansion	Telephone
2	5	In	Out	Warning	Output	Output
3	4			2		Line 2
						2

Wire Color Codes

Cat5

4 pair UTP

RING

brown

pair 4 TIP

	brown/white
	green	RING
pair 3	green/white	TIP
	orange	RING
pair 2	orange/white	TIP
		RING
pair 1	blue
		TIP

Solid Color Twisted-Pair Wire

blue
white	pair 3
yellow
black	pair 2
red
green	pair 1

			3
1	6		5
		1	Line 1
2	5		2
3	4		3
			5
	Line 1

blue/white

Modular connectors

6 position connectors 8 position connectors

Typical Installation

Each line is individually surge protected to 50 Joules and

Install this jumper for normal	4000 Amps. Some surges contain sufficient energy that
operation. Remove to disconnect
	although your system has been protected, the surge
telephone service from the system.
	circuit will be unable to provide additional protection.
	When this happens, the red light for that line will turn on
	and the module needs to be returned for service.

					PR2		PR3
							PR2
		PR1			PR1
							PR1
		R T		T R T R		T T R T R R
1	2 3 4 5 6		1 2 3 4 5 6			1 2 3 4 5 6
RJ-11			RJ-14			RJ-25
Single line telephones,			Dual line telephones &			Rare
answering machines &			answering machines			3 line KSU
modems

PR2

PR3 PR1 PR4

T R T R T R T R 1 2 3 4 5 6 7 8

RJ-45 (wired to TIA T568A standard) Ethernet (both 10BaseT and 100BaseT) Structured wiring of phones and data lines

(There are other wiring standards. For residential use, we recommend that RJ-45 jacks be wired to the T568A standard.)

CAT-5 jumper

(included)

Wiring a 110 connector

From telephone company exchange 2 lines

H612				Entry Module (surge,disconnect)
				ChannelPlus model H612
	From NTE
	Line 2
1	6		Disconnect	Surge	Expansion	Telephone
2	5	In	Out	Warning	Output	Output
3	4			2		Line 2
						2
						3
1	6					5
				1		Line 1
2	5					2
3	4					3
						5
	Line 1

Keep sheath close to connector Untwist .5” max.

110 punch down tool

The 110 is a sophisticated insulation displacement connection system. To push the wire between the contact blades, use only a 110 punch down tool. Using a screwdriver or needle nose pliers may not seat the wire properly and can damage the contacts.

Note order of colors

2 lines to telephone wall plates.

Wiring a Cat-5 jack

Expansion

Ports

In

Out

Telephone Expansion Hub (4 lines x 8 phones) ChannelPlus model H618

Telephones

R

T 4

R

T 3

R

T 2

R

T 1

H618 telephone expansion hub

Line 2

2 3

5 Line 1

2 3 5

Use self adhesive sticker provided to label the output I.D.

1

Keep sheath close to jack.

Follow color code for T568A jacks. Position first pair to channel closest to end of jack. (Do not untwist conductor pairs more than 0.5" from the termination point.)

2

110punch-

down tool

Using a 110 punch-down tool, push wires into channels and trim. Repeat for subsequent pairs.

3

When all conductor pairs are terminated, snap on strain relief caps.

Use CAT-3 or CAT-5
wires, 2 lines to 8	1	4
telephone wall	3	6
	2	5

1	4
2	5
3	6

Colors of OpenHousetm wiring

CAT-5, 4 UTP	RG-6 coax
Telephone
(from telco)
Telephone	Downstream/External
(in house)
	(to TVs)
Data
Security	Upstream/Internal
	(from modulators)

Wiring Modular Plug (T568A)

Insert wires in this order:

White/Green

Green

White/Orange

Blue

White/Blue

Orange

White/Brown

Brown