Cobra Electronics CXR700C Press the Channel Up or Channel Down button to, Privacy Code Scan

Page 12

Operation

Mode Functions

 

 

 

 

Introduction

Operation

Customer Assistance

Warranty

During channelscan (while receiving an incoming transmission), you can choose from the following:

a. Press and hold the Talk button to communicate on that channel. Your radio will remain on that channel and return to Standby mode.

b. Press the Channel Up or Channel Down button to

Privacy Code Scan

•

Your microTALK radio can automatically scan the Privacy Codes (either CTCSS 01 through 38 or DCS 01 through 104) within one channel. Only one set of privacy codes (CTCSS or DCS) can be scanned at a time.

Select Channel

To scan privacy codes:

resume scanning channels.

If you press the Talk button while scanning, but more than

10 seconds after receiving a transmission, you will transmit on the channel on which you last received a transmission. This will return the radio to Standby mode.

If you do not press any button within 10 seconds after receiving a scanned transmission, your radio will automatically resume scanning channels.

During channel scan (while not receiving a transmission), you can choose from the following:

a. Press and hold the Talk button to communicate on the channel or channel/privacy code that was displayed before you entered mode functions or the channel on which, during scanning, you last received a transmission. This will then return the radio to Standby mode.

b. Press the Mode button to proceed to set privacy

code scan on the channel that was either displayed before you entered mode functions or on which, during channel scanning, you last received a transmission (see page 19 for further details).

c. Press the Lock/Enter button to return to Standby mode on the channel/privacy code that was displayed before you entered mode functions or the channel on which, during scanning, you last received a transmission.

Mode Button

ScanPrivacy Codes

Channel Button

1.While in Standby mode, press the Channel Up or Channel Down button to choose the channel on which you wish to scan privacy codes.

2.Press the Mode button until either the CTCSS or the DCS icon appears on the display and the Scan icon and the privacy code numbers flash on the display.

3.Press the Channel Up or Channel Down button to begin scanning privacy codes within the channel you selected.

The Scan icon will continue to be displayed when privacy code scan is on. Your radio will continue to scan privacy codes and stop as an incoming transmission is detected. Your radio will remain on that channel/privacy code for 10 seconds.

While setting privacy code scan, if you do not press any buttons for 15 seconds, your radio will automatically return to Standby mode on the channel/privacy code that was displayed before you entered mode functions.

18

Nothing Comes Close to a Cobra® 19

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Making Life Easier and Safer For Assistance in Canada or the U.S.AAutomated Help Desk Customer Assistance OperatorsProduct Features FeaturesRechargeable Battery Pack and Desktop Charger To install or replace battery packReplace battery compartment cover and belt clip Caring for YourmicroTALKRadioUsing Your Radio Battery LowAuto Battery Save For charging microTALK radios in desktop chargerTo toggle between high and low power Listening for a ResponseCall Button To alert another person that you are callingTo turn the lock feature on or off Light/Max Range To briefly turn off auto squelchTo turn maximum range extender on To attach a speaker/microphoneMode Functions Scrolling through Mode FunctionsPrivacy Codes Set Ctcss Privacy Codes To select a Ctcss privacy codeSet DCS Privacy Codes To select a DCS privacy codeTo turn VOX mode on or off Voice ActivatedTransmit VOXMemory Locations To set VOX sensitivityPress the Mode button to Choose one of the followingTo recall a stored memory channel location While recalling a stored memory locationTo de-program a memory location Channel ScanFlash on the display ThroughPress the Mode button to proceed to set privacy Press the Channel Up or Channel Down button toPrivacy Code Scan Memory Location Scan To scan memory locationsTo change call settings VibrAlert and Call AlertTo change a call tone setting To change keystroke tonesTo turn roger beep on or off General Specifications FCC License General SpecificationsProduct Service Safety and Trademark AcknowledgementProduct Service Safety Information for microTALK RadiosWarranty LimitedOne-Year Warrantyon Radios & Charger
Top Page Image Contents