Cobra Electronics CXT90 owner manual Using Your Radio, To connect a wall charger/adapter

Page 4
Turning on Your microTALK® Radio

Operation

Using Your Radio

 

 

 

 

Introduction

Operation

Customer Assistance

Warranty

Speaker/Microphone/Charge Jack

Speaker/Microphone

To attach a speaker/microphone:

/ChargeJack

1. Open the speaker/microphone/charge

 

tab on top of your microTALK® radio.

2. Insert the speaker/microphone accessory plug into the speaker/microphone/charge jack.

To connect a wall charger/adapter:

1.Open the speaker/microphone/charge tab on top of your microTALK® radio.

2.Insert the wall charger/adapter plug

into the speaker/microphone/charge jack.

Quick Start

1. Press and hold the Mode/Power button to turn on your radio.

2.Press the Channel Up or Channel Down button to select a channel.

Both radios must be tuned to the same channel/privacy code to communicate.

3.Press and hold the Talk button while speaking into the microphone.

4.When finished talking, release the Talk button and listen for a response.

Mode/Power Press and hold the Mode/Power button until you hear a series of audible tones indicating the radio

is on.

Your microTALK® radio is now in Standby mode, ready to receive transmissions. The radio is always in Standby mode except when the Talk, Call or Mode/Power buttons are pressed.

Battery Low

Battery Low

When battery power is low, the Battery Low icon

 

will blink. Your batteries should be replaced or

 

recharged, if using rechargeable batteries.

Auto Battery Save

 

 

Battery Save Mode

If there are no transmissions within 10 seconds,

 

the radio will automatically switch to Battery

 

 

Save mode and the Power Saver icon will flash

 

 

in the display. This will not affect the radio’s

 

 

ability to receive incoming transmissions.

 

Communicating with Another Person

 

1. Press and hold the Talk button.

Talk Button

 

 

2. With the microphone about two inches (5 cm)

 

 

from your mouth, speak in a normal voice.

 

 

3. Release the Talk button when you are

 

Two Inches (5 cm)

finished talking and listen for a response.

 

You cannot receive incoming calls while

 

from Mouth

 

 

pressing the Talk button.

 

 

Both radios must be tuned to the

 

 

same channel to communicate.

 

To Select a Channel

 

With the radio on, select any of the

Channel Button

 

 

22 channels by pressing the Channel Up

 

 

or Channel Down button.

 

 

Both radios must be tuned to the

 

Channel Number

same channel to communicate.

 

 

 

 

Channels 1 through 7 are shared with FRS/

 

 

GMRS. Channels 8 through 14 are FRS only.

 

 

Channels 15 through 22 are GMRS only.

 

 

See page 14 for FRS/GMRS frequency

 

 

allocations and compatibility charts.

 

 

 

Nothing Comes Close to a Cobra® 3

2

Image 4
Contents Making Life Easier and Safer Automated Help DeskCustomer Assistance Operators QuestionsLimited One-Year Warranty on Radios & Charger Warranty and Trademark Product FeaturesAcknowledgement Rechargeable Batteries and Charger Caring for YourmicroTALK RadioTo charge batteries in radio To connect a wall charger/adapter Using Your RadioOr Channel Down button To temporarily turn off auto squelch To turn maximum range extender onTo turn maximum range extender off To turn the lock on or offScrolling Through the Mode Function Set Ctcss Privacy CodesTo select a Ctcss privacy code Privacy CodesMode Functions Channel Scan To scan channelsOn the display Privacy Code ScanFive Call Tone Settings To change a call tone settingOn or off setting is displayed Roger Beep Confirmation ToneGeneral Specifications and Licensing General SpecificationsSafety Information for microTALK Radios Normal PositionProduct Service Product Service Questions