Uniden 2155, 2165 quick start Selecting the message record time, Selecting Ring Time Switch

Page 26

Selecting the message record time:

You can set your answering system to record a message up to one or four minutes long.

One minute option : move the REC TIME switch to 1.

 

 

 

Four minutes option : move the REC TIME switch to 4.

 

 

 

Announce only feature:

 

RING TIME

REC TIME

 

 

2/4/TS

ANN/4/1

 

 

 

 

The announce only feature plays an outgoing message, but

 

 

 

will not allow the caller to leave a message. Move the REC

 

 

 

TIME switch to the ANN position.

 

 

 

 

The message counter LED displays

when the system is

 

 

 

on standby.

 

voice memo

 

 

Pre-recorded outgoing message for Announce only feature is:

greeting

 

volume

“Hello, no one is available to take your call.” (twice)

 

 

 

 

 

speaker status

delete

play

 

 

 

 

 

 

 

Selecting a PIN code:

 

 

 

 

To play your messages from a remote location, you will need to enter a two digit Personal

Identification Number (PIN) code ( 0

0 9

9

(. To select a PIN, perform the

following steps.

until a tone sounds and the LED displays 00.

1.

On the base, press and hold pin

2.

To set the first number, press

or

repeatedly to scroll from 0 to 9. When

 

the desired number appears in the display, press

pin .

3.

To set the second number, press

or

 

to scroll from 0 to 9. When the

 

desired number appears in the display, press

pin . Then the entered PIN code is

 

announced.

 

 

 

Selecting Ring Time Switch:

The ring time/toll saver switch allows you to set the number of rings the caller hears before the answering system plays your outgoing message.

You can set the switch to answer after two rings or after four rings. Once the greeting has started, you can stop it when you pick up the call at the handset or base. In the TS (toll saver) position, the answering system picks up after 6 rings if you have new messages, and after 9 rings if there are none.

This way, if you call long distance to check your messages, you can hang up after the seventh ring to avoid billing charges.

 

 

 

 

 

 

 

 

 

RING TIME

REC TIME

 

2/4/TS

ANN/4/1

Using Your Answering System

Playing your messages

The base LED shows the number of total messages on the display. If the display is blinking, then there are new messages waiting for you. After you play your new messages you can then play old messages.

1. Press

. The system announces the number of new and old messages, then the

incoming messages are played.

2.When all new messages have played, a tone is heard. The message counter LED stops flashing to indicate that all of the new messages have been reviewed.

3.After you have reviewed all your messages, you can play your old messages again. Press

and follow the instructions above.

20

Page 25 Page 27
Image 26
Page 25 Page 27
Contents DSS 2155 Installation & Safety Choosing the best location for your DSS2155/DSS2165Start AC Adaptor cord plug the AC Adaptor into Raise the antennaPress firmly until it clicks into place Press the battery cover and slide it offMake sure the plug is the right way round Handset off the Base Unit To hang up press talkHandset on Base Unit System beeps and begins to play the next message Press new messages play firstPress during playback of messages Contents Controls & Functions Headset jack Delete/Page key Belt clip slot Select keyRear Charge Cradle Welcome Card Gently pull one side of the beltclip to releaseCleaning the battery contacts Battery use time per chargeWhen the battery charge becomes low Ringer tone and volumeBasic phone operation To answer a call phone ringingRedial from standby Call TransferRedialling a Call To transfer from handset to base unitCall WAITING/FLASH Travelling OUT of RangeKEY Lock / Unlock Redial from the Base UnitUse to delete characters as needed Storing Phone Numbers and NamesWith the Handset Use to enter a pause. The screen displays PMemory Dialling from Standby Memory dialing from talk modeMaking Calls with Memory Dialling Display a Memory Number or NameYou would like to edit Press Rocket DialStoringandeditingtherocketdial Press to savePress and hold until Memory Store is displayed Making Callswith RocketdialPAGING/INTERCOM Press to move the pointer down toWay radio feature using an optional handset WAY ConversationHandset RegistrationPlace the handset in the Main Base Unit Fig NumberName Tagging When the Telephone RingsCaller ID Number of callsDeleting all Caller ID names/numbers Viewing the Caller ID Message ListDeleting Information from the Caller ID List Storing Caller ID messages in Memory dialing Using the Caller ID ListCalling a party from the Caller ID list To add a name to the stored number refer toPreset message FeaturesSetting your greeting Answer SystemSelecting the message record time Selecting Ring Time SwitchUsing Your Answering System Playing your messages Deleting Messages Deleting individual messages Repeating a messageSkipping a message Deleting all messagesChecking the Date and Time Setting the Date and TimeSetting the Time Stamp On/Off Press or to select the required minuteYour PIN code. If the Answering Press # Remote access away from homeRemote room monitor ThenTrouble Shooting Uniden New Zealand Limited One Year Limited WarrantyWarrantor Uniden Australia Pty Limited A.B.N 001 865Uniden Australia Pty Limited Uniden New Zealand Limited
Top Page Image Contents