Panasonic SL-S292 Anti-Shock Function Anti-Skip System Maintaining the Lens

Other Play Methods

The letters such as A in the various illustrations refer to the descriptions in the “Location of Controls” section (see page 2).

Skip play

The disc plays from the specific track through to the end, then play stops automatically.

Preparation: Put unit in stop mode.

1	RANDOM
	RESUME NORMAL
	L
2	Select the desired track.
	6	5

A

:9

3

D		1;
Random play
1	RANDOM
	RESUME	NORMAL
L
2
D	1;
Release	RANDOM
	RESUME	NORMAL

L

For your reference:

≥It is also possible to press [9] while the unit is in stop mode to change the first track to be played. (All tracks are played eventually, regardless of which is played first.)

≥Program play is not possible in the random mode.

Resume play

This function allows you to listen from the beginning of the track where play stopped because the unit was powered off (or switched to stop mode). It is useful when listening to CDs in the car, etc.

RANDOM
RESUME	NORMAL
L
Release
RANDOM
RESUME	NORMAL

L

For your reference:

≥If [RESUME, RANDOM, NORMAL] is put in the [RESUME] position, the all-track repeat function will be activat- ed automatically as soon as the unit is powered on.

≥If power is cut off near the end of a track (off mode), playback may resume from the beginning of the next track.

≥If the unit is powered off while a disc was playing and then a new disc is inserted, play will begin from the middle of the new disc because the unit remembers the position where play stopped on the previous disc.

Program play

Up to 24 tracks can be entered in the programmed sequence. Preparation: Put unit in stop mode.

1	RANDOM
	RESUME	NORMAL
	L
2	Select the desired track.
	6	5
	A	9
	:

3 Register in sequence.

(The indication “M” and the programmed sequence appear on the display.)

	MEMORY/
F	RECALL

4 Repeat steps 2 and 3 to program all the desired tracks.

5

D 1;

∫To program the same track in the sequence more than once

∫After step 3, press [MEMORY/RECALL] desired number of times.

∫If “'” is displayed

∫No more tracks can be programmed.

∫To confirm the contents of the program

∫Press [MEMORY/RECALL] while the disc is playing. (The number of the programmed tracks appear on the display in se- quence.)

∫To delete the entire programmed sequence

∫Press [∫, OPR OFF].

Repeat function

Press during play or stop mode.

` E

The setting is switched in the sequence indicated below each time [`] is pressed.

1-track repeat (1 `)( -------------------------------------	]
One track is repeated.
v
All-track repeat (ALL `)
All the tracks on the disc are repeated
v

Cancel (no indicator is shown) ======}

For your reference:

If [`] is pressed during program play, only the tracks in the program are repeated.

(The indication “ALL” is not displayed.)

Changing the sound quality

Press during play or stop mode.

S-XBS

J

The setting switches in the sequence indicated below each time [S-XBS] is pressed.

S-XBS>Cancel (no indicator is shown) ^========b

S-XBS:

Select this setting to boost the low-range response.

B S-XBS

Anti-Shock Function (Anti-Skip System)

Maintaining the Lens

Anti shock works by reading audio data and storing it in memory. The unit then fills in interruptions caused by bumps and vibrations with data from the memory up to 10 seconds worth.

This unit also incorporates a powerful anti-shock mech- anism that prevents skipping caused when play speed is changed by swinging of the unit.

Press during play or stop mode.

A.SHOCK

I

The following indicator appears on the display.

Note!

≥The anti-shock setting can be changed during play, but this may cause a slight interruption in the sound because the disc’s rotation speed changes.

≥During anti-shock operation, the disc rotates at a high- er rate than usual to collect extra audio data. This could result in a slight increase in disc rotation noise.

Listening to sound with the unit con- nected to an audio system

The anti-shock function uses digital signal compression technology. It is recommended that the anti-shock func- tion be canceled if the unit is connected to a home

Open the lid and clean the lens as shown in the figure. Use a cotton swab to gently wipe off any finger-prints. Recommended product: Lens cleaner kit (SZZP1038C)

Air blower for camera lens

Lens

B

Note!

A.SHOCK

audio system.

Lens

If you have pressed [A.SHOCK] when the unit is in stop mode, press [1 ;] to start play.

When bumps continue repeatedly

The following indicator appears on the display and sound is interrupted.

B

To cancel the anti-shock function

Press [A.SHOCK] again.

User memo:

DATE OF PURCHASE

DEALER NAME

DEALER ADDRESS

TELEPHONE NUMBER

RQT6165

4