Pioneer MEP-7000  To disconnect a USB storage device, Disconnect the USB storage device

Page 26

HANDLING DISCS AND OTHER MEDIA

CAUTION

Depending on the device used, proper playback may not be possible with all USB storage devices. Pioneer assumes no responsibility for any loss of data resulting from connecting any given USB device to this unit.

•Proper operation may not be possible when a USB storage device is connected through a USB hub.

•Even if a USB hub is used to connect multiple USB storage devices, the second and later devices cannot be used.

•Operation cannot be guaranteed when using a USB storage device with installed flash card reader.

•When connecting a USB storage device utilizing two USB cables, connect both cables to this unit’s USB ports.

•If an electrical current stronger than the allowable current is applied to the unit’s USB1 port or USB2 port, the unit may stop supplying power to the USB storage device, thus terminating transmission. In this case, a message will be displayed in the center display of the unit, and the stop indicators for USB1 and USB2 will flash red simultaneously. To restore normal operation, disconnect all USB storage devices connected to the unit, then hold either of the USB STOP buttons depressed for two seconds or more. Avoid connecting the USB storage device from which the excess current was detected and other USB storage devices connected through a bus-powered USB hub. If normal operation is not restored through this method, turn the power of this unit off, and then turn it back on.

To disconnect a USB storage device

1Hold the STOP button pressed for two second or more.

2Confirm that the indicator goes out.

Confirm on the front panel that the red indicator for the connected port has change from flashing to off.

3Disconnect the USB storage device.

MEMO

•After the indicator goes out, if the STOP button is held depressed for two seconds or more, the USB storage device's connection can be reinitiated without the need to physically disconnect and reconnect it.

CAUTION

When disconnecting a USB storage device, always be sure to perform the STOP operation first.

If the STOP operation is not completed before disconnection, cue/loop memory and playlist update may not occur properly, resulting in the loss of data. Also, the USB storage device may becomes unreadable, or other substantial damage may occur.

In the case of a HDD device, do not subject it to impact or vibration during use.

Always disconnect the USB storage device before turning off the power to this unit.

26

En

Page 25 Page 27
Image 26
Page 25 Page 27
Contents MEP-7000 Class Operating Environment Contents Features Manipulator styleNormal style Super Fast Pitch Bend MemoPitch Bend Frame SearchBack CUE Tempo Control RangeMaster Tempo CUE/LOOP MemorySpecifications Control cords x DJS 1 Set Dedicated remote control cable Comfirm AccessoriesAudio cables x Power cord USB auxiliary power cable Warranty cardRegarding Playable Discs and Files Types of Discs Playable on this UnitFAT, FAT32, HFS+ About MP3/AAC Disc PlaybackAbout Playback from USB Storage Device MPEG-1 About MP3 FilesAbout AAC Files MPEG-2About WAV Files About Aiff FilesInstallation Guidelines System connections ConnectionsNormal Style Connections Connecting another mixer Connection to external monitor pin-jack connectorConnecting other components Connecting a stereo amplifier when not using DJ mixerConnecting a computer Connecting the power cordManipulator Style Connections Audio interface sold separately Audio cable MixerDrive Unit Parts and Their FunctionsFront Panel Control UnitBrowse button P Time mode/auto cue button TIME/A.CUE TimeCUE P Track Search ,  buttons P Search ,  buttons P MIX button PCenter Display Rear Panel Loading and Removing Discs Set the drive unit’s front panel Power switch to onHandling Discs and Other Media Insert a discConnecting and Disconnecting USB Storage Devices Writing Management Data to a USB Storage Device To disconnect a USB storage device Disconnect the USB storage device Source icons Start PlaybackBrowse Screen  Library Browsing File Browsing and Library Browse icons  File Browsing Select the Track View Properties of the Currently Playing Track Track/folder jump M3U FileTrack Selection with a USB Keyboard  Editing playlist namesTAB  Playlist display composition Playlist listing Using the PlaylistWhen a Playlist is Open  To record tracks in a playlist To close a playlist  Changing the playlist’s track order To delete tracks from a playlist  To delete a playlistBasic Controller Operations Track Skip Switching the JOG Mode Using the Track Search ,  buttons JOG Dial FunctionApplying a Master Tempo Setting CUE PointsChanging the Play Speed Changing the Auto Cue Level Auto CUE FunctionTurning Auto Cue ON/OFF Press the Pitch Bend +, buttons to change the valueCUE POINT/LOOP Point Memory Advanced Operations SectionLoop Play Spin Play Scratch PlayEffect Screen JOG Break PlayAbout Bubble About ScratchAbout Trans About Roll Jog break effectAbout JET Effect HoldAbout WAH MIX ScreenEffect off Sets the Auto MIX function ON/OFF Instant Change Function  MIX mode selectSets the BPM Sync ON/OFF Press the Auto MIX function button to set to on About Fader Start Play Automatic Playlist Playback Press the play/pause  button for controller aAbout DJS Software Software END User License AgreementCopyright Warning  Installation Procedure Installing DJS Software Precautions regarding installation User Registration Card Address Pioneer Electronics USA INCRegarding Online Support Disclaimer Before installing Important Driver Installation Using the accessory CD-ROM to install the application About the Driver ProgramFor Windows  Connecting this unit to the computerFor Windows XP Follow the instructions that appear on the screen Setting the buffer size  Confirming the driver versionTwo Styles of Play Using DJ SoftwareSupported DJ softwares Normal StyleConnect to the computer Preparing Your DJ Software Program Control in Normal Style Press Load a or B button  Control using Manipulator StyleSelect PC on the Browse screen Use the controller to operate the DJ softwareUsing Midi for Computer Control  button  Setting a Midi channelPress the Utility button Press the PC function button Comments Midi Message TableInterface Name TypeSelect UP Rotary Selector DialSelect Down Push Load aEnjoying CD-G Karaoke Select CD-G Play ModeTo Cancel CD-G Play Mode To Play a CD-G DiscSettings Using the UtilitySetting Method CD-G Setting the browse type  Writing data to USB storage device Creating LibrariesBacking UP User Data  Reading data from a USB storage deviceConfirm message To Perform a Factory ResetTurn power OFF and on again Troubleshooting Adjust button About the Driver Program About the LCD ScreenAbout OEL Organic EL Screens Error Code Error Type Media Description Error Message DisplayMEP-7000 Updates Software Limiting Conditions CD-TEXTDisclaimer Pioneer Corporation
Related manuals
Manual 206 pages 60.68 Kb

MEP-7000 specifications

The Pioneer MEP-7000 is a cutting-edge digital DJ controller that has redefined the landscape of live performance and mixing. Designed with the professional DJ in mind, this unit combines innovative technologies and an intuitive user interface, making it a powerful tool for both live performances and studio sessions.

One of the most prominent features of the MEP-7000 is its two-deck playback capability, allowing DJs to mix and manipulate two audio sources simultaneously. This dual functionality is complemented by its comprehensive array of onboard controls, including large jog wheels, faders, and multifunction buttons, making it easy to access various functions and effects on the fly. The device's built-in 24-bit sound card ensures high-quality audio output, providing crystal-clear sound to all connected systems.

Another key technology integrated into the MEP-7000 is its compatibility with multiple media formats, including CD, USB drives, and even computer-based music libraries. This versatility allows DJs to seamlessly transition between different media types, adapting to any performance environment. The unit supports various audio file formats, ensuring that users can work with their preferred music without limitations.

The MEP-7000 also features an advanced display interface that provides real-time feedback on track information, waveforms, and settings. DJs can easily navigate through their libraries, adjust effects, and make crucial performance decisions quickly, without the need to glance away from the crowd.

In addition to its robust performance capabilities, the MEP-7000 incorporates various effects and sound manipulation tools, including echo, flanger, and reverb, which can be applied in real-time. This allows DJs to add their unique flair to mixes, enhancing the overall live experience for their audience.

User-friendliness is a hallmark of the MEP-7000, with its layout designed for efficiency and ease of use. The controller's ergonomic design facilitates comfortable operation during extended sets, while its durable build ensures reliability in high-energy environments.

Overall, the Pioneer MEP-7000 stands out as a versatile and powerful solution for today's professional DJs. With its combination of high-quality sound, multiple format compatibility, and intuitive controls, it remains an essential piece of equipment for any serious DJ who seeks to elevate their performance to new heights.
Top Page Image Contents