Pioneer AVIC-88DVD, AVIC-9DVD, AVIC-90DVD, CNDV-50MTP, AVIC-880DVD Fied Areas to Avoid

Message	When	What to do
Route calculation was not possible.	Route calculation has failed because	• Change the destination.
	of malfunction of map data, software,	• Clean the disc.
	hardware, or disc.	• Consult the Pioneer Local dealer if
		this message persists.
Route calculation was not possible	The destination is too far.	• Set a destination closer to the start-
because the destination is too far.		ing point.
		• Set one or more way points.
Route calculation was not possible	The destination or way point(s) is too	Set a destination [and way point(s)]
because the destination is too near.	close.	farther from the starting point.

Route calculation was not possible due to traffic regulations.

•The destination or way point(s) are in a Control Traffic Zone (CTR) and the route calculation is hampered.

•Your vehicle is currently in a Con- trol Traffic Zone (CTR) and the route calculation is hampered.

•Set a destination and way point(s) outside the CTR if you know where the restricted area is.

•Try the destination or way point(s) away from the currently set points to some extent.

•Drive your vehicle to an unre- stricted area and reset the destina- tion and way point(s).

Appendix

Route calculation was not possible	The destination, way point(s), or	• Set a destination and way point(s)
because no guidance can be pro-	starting point are in an area where	on roads.
vided around the destination or the	no road exists (e.g. a mountain) and	• Reset the destination after you
starting point.	the route calculation is impossible.	drive the vehicle to any road.
There is no route to the destination.	The destination or way point(s) are in	Change the destination.
	an isolated island, etc. without a ferry
	and the route calculation is impossi-
	ble.
The route could not avoid the speci-	If route setting cannot avoid speci-	If the current route is not desired, set
fied area.	fied Areas to Avoid.	destination or way points that do not
		pass through the Areas to Avoid.
The route could not avoid the speci-	If the route to the destination (or way	If the current route is not desired, set
fied area.	point) cannot be established by	destination or way points that do not
Toll road has not been avoided.	bypassing toll roads (including toll	pass through toll roads (including
	areas) and Areas to Avoid.	toll areas) and Areas to Avoid.
Ferry has not been avoided.	In case a ferry route was included in	If the current route is not desired, set
	the route to the destination or way	destination or way points that do not
	points even though “Avoid Ferry”	pass through a ferry route.
	was set to “On”.
Toll road has not been avoided.	If the route to the destination (or way	If the current route is not desired, set
	point) cannot be established by	destination or way points that do not
	bypassing toll roads (including toll	pass through toll roads (including
	areas).	toll areas).
The address does not exist.	If the house number is entered with-	Re-enter the existing house number
Do you want to continue?	out specifying City or Street and that	by following the instructions shown
	house number does not exist on the	on the screen.
	data.	Or, proceed to the next step without
		entering the house number and
		specify the City or Street first.
There is no applicable data for the	If the history data of the City could	Once the search is performed to
selected city. Automatically returning	not be used (for example, in case	specify the City, the result is saved as
to list.	that the history data of the City that	a history. The data of the specified
	was used in the POI Search cannot	City, however, may not be hit by the
	be found in the Address Search.)	different search criteria. In this case,
		try another search method or change
		the destination.
There is no Freeway in this area.	If no freeway was found in the	Set the destination or way points
	selected zone.	using another search method or
		change the location of the destina-
		tion or way points.

70