Califone 2455AV-02 owner manual Vol, Tre+2 ba-1, Treble and Bass Controls, PLL Radio Function

GETTING STARTED

The LED display will be in red (for standby mode) when the ‘Power’ button is pushed. Pushing the LED will cause the LED to be green indicating the unit is fully powered up.

•Depressing the ‘Tape’ button will cause the LCD display to show ‘Tape’.

•Depressing the ‘AM/FM’ button will cause the LCD display to show ‘AM’ or ‘FM’.

•Depressing the ‘CD’ button will cause the LCD display to show ‘Disc’.

DIGITAL VOLUME CONTROL

•The volume control is preset to automatically turn on at volume level "26" upon power up. Press ‘VOL ▼’ to reduce the volume, the level will be shown in the LCD panel. Minimum volume will show ‘00’ on the LCD display.

Electronic Volume Control Display

VOL 26

• Press ‘VOL ▲’ to increase the volume. The maximum volume is ‘40’ on the LCD display.

TREBLE AND BASS CONTROLS

‘TREBLE ▲’ and ‘TREBLE ▼’ can be used to adjust the Treble up and down respectively, while ‘BASS ▲’ and ‘BASS ▼’ can be used to adjust the Bass up and down respectively. Both Treble and Bass can be adjusted in

the range of +5 to –5. Treble Bass

tre+2 ba-1

PLL RADIO FUNCTION

•Press ‘AM/FM’ to select the desired reception band. Extend the telescoping antenna for FM. There is a built-in antenna for AM reception. For FM stereo reception the ‘stereo’ will show on

the LCD display.

AM Band Selection

AM 520KHz

•Press the ‘TUNER ▲’ or ‘TUNER ▼’ button repeatedly until the desired station shows on the LCD display. •To automatically scan through the frequency bands, hold the ‘TUNER’ button down until you see the speed

of the LCD display increase. Scanning will stop when a strong signal is detected.

1.Insert a blank tape into cassette Deck 1.

2.Press the ‘PAUSE’ button then the ‘RECORD’ button on Deck 1 to prepare for recording. As the ‘RECORD’ button is pressed the ‘PLAY’ button will follow.

3.Press ‘PAUSE’ again to start recording.

Dubbing (Recording from Tape 2 to Tape 1)

1.Insert a blank tape into cassette Deck 1, and the source or prerecorded tape into Deck 2.

2.Press the ‘PAUSE’ button then the ‘RECORD’ button on Deck 1 to prepare for recording. As the ‘RECORD’ key is pressed the ‘PLAY’ button will follow.

3.Press the ‘PLAY’ button on Deck 2, the ‘PAUSE’ button on Deck 1 will release automatically and

recording will begin.

Note: Every new cassette tape has erase prevention tabs. Commercially prerecorded tapes have the tabs removed to prevent recording over the original material or accidental erasure. Cover the openings with adhesive tape if you wish to record over such cassette tape.

To Stop Recording

Press the ‘STOP/EJECT’ button on Deck 2 or press the ‘PAUSE’ key on Deck 1 to momentarily stop recording.

Cueing with the Tape 1 Counter

Rewind the tape to the beginning. Press the ‘RESET’ button to reset the counter to (000). Use the Tape 1 Counter Display to note precise points on an audio tape during playback and to cue the tape to those precise points using the ‘FAST FORWARD’, ‘CUE’, or ‘REWIND/REVIEW’ buttons.

Compact Disc Player Operation

The 2455AV-02 Programmable Compact Disc Player plays both 12cm and 8cm CDs, CD-R, CD-RW without requiring an adapter. Up to 20 tracks can be programmed for play.

Loading a Compact Disc

1.Lift to open the CD door and see “OPEN” on the LCD display.

2.Place a CD in compartment with label side up.

3.Press the CD door down to close.

Compact Disc Play

To play a loaded CD:

1.Turn power ON.

2.Set the ‘FUNCTION’ Selector to CD.

3.The LCD will show the number of tracks and playing time.

4.Press the ‘PLAY/PAUSE’ button.

The CD Display will show the current track and playing time.

To pause a playing CD

Press the ‘PLAY/PAUSE’ button again. The pause indicator “II” will appear on the display. Press ‘PLAY/PAUSE’ again to resume play.

6 11