Sharp GX-M10H(OR), GX-M10H(RD) Timer and sleep operation Remote control only, „ Timer playback

Timer and sleep operation (Remote control only)

Timer playback:

The unit turns on and plays the desired source (CD, TUNER, USB, iPod, AUDIO IN) at a preset time.

This unit has 2 types of timer: ONCE TIMER and DAILY TIMER.

Once timer:

Once timer play works for one time only at a preset time.

(“” indicator).

Daily timer:

Daily timer play works at the same preset time every day. For example, set the timer as a wake-up call every morning.

(“DAILY” indicator).

Using the once timer and daily timer in combination:

For example, use the once timer to listen a radio programme, and use the daily timer to wake up.

1 Set the daily timer (pages 19 - 20). 2 Set the once timer (pages 19 - 20).

	1 minute or more
Daily timer			Once timer
Start	Stop	Start	Stop

„Timer playback

Before setting timer:

z Check that the clock is set to the correct time (refer to page 6). If it is not set, you cannot use the timer function.

z For timer playback: Plug in USB or load discs or dock iPod to be played.

1Press the ON/STAND-BY button to turn the power on.

2Press and hold the CLOCK/TIMER button.

3Within 10 seconds, press the or button to select “ONCE” or “DAILY”, and press the ENTER button.

4Within 10 seconds, press the or button to select “TIM.SET”, and press the ENTER button.

5To select the timer playback source (CD, TUNER, USB, iPod,

AUDIO IN), press the or button.

When you select the tuner, select a station by pressing the or button, and then press the ENTER button. If a station has not been programmed, “NOPRESET” will be displayed and timer setting will be cancelled.

6Press the ENTER button to adjust the hour. Press the

or button and then press the ENTER button.

7To adjust the minutes, press the or button and then press the ENTER button.

8Set the time to finish as in steps 6 and 7 above.

9Adjust the volume using the VOLUME control, and then press the ENTER button. Do not turn the volume up too high.

10Press the ON/STAND-BY button to enter the power stand-by mode. The “TIMER” indicator lights up and the unit is ready for timer playback.

TIMER

REMOTE

SENSOR

11 When the preset time is reached, playback will start. The volume will increase gradually until it reaches the preset volume. The timer indicator will blink during timer playback.

12 When the timer end time is reached, the system will enter the power stand-by mode automatically.

Once timer:

The timer will be cancelled.

Daily timer:

The timer operates at the same time every selected day. It will continue until the daily timer setting is cancelled. Cancel the daily timer when it is not in use.

Notes:

zWhen performing timer playback using another unit connected to the USB terminal or AUDIO IN socket, select “USB” or “AUDIO IN” in step 5. However, if the source is set to USB, make sure there is no iPod or iPhone docked to the unit.

zThis unit will turn on or enter the power stand-by mode automatically. However, the connected unit will not turn on or off. To stop the timer playback, follow step “Cancelling the timer setting” of this page.

Checking the timer setting:

1 Turn the power on and press and hold down the CLOCK/TIMER button.

2 Within 10 seconds, press the or button to select “ONCE” or “DAILY”, and press the ENTER button.

3 Within 10 seconds, press the or button to select “TIM.CALL”, and press the ENTER button.

Cancelling the timer setting:

1 Turn the power on and press and hold down the CLOCK/TIMER button.

2 Within 10 seconds, press the or button to select “ONCE” or “DAILY”, and press the ENTER button.

3 Within 10 seconds, press the or button to select “TIM.OFF”, and press the ENTER button. Timer will be cancelled (the setting will not be cancelled).

19