Specifications, Full Range Models, HPR152F

Specifications, Full Range Models

Frequency Response, ±6dB Frequency Range, -10dB limit Maximum Peak SPL Nominal coverage, H x V Directivity Index Directivity Factor Transducer Description

Acoustic Crossover Freq. Amp Power

Input Sensitivity

Input Headroom/Clipping

Input Connector/Impedance

Output Connector

HPR152F

53-18k Hz

50-20k Hz

135dB

90°x60°

9.4

8.7

15” (381mm) transducer with 3” (76mm) voice coil 1” (25mm) throat compression driver

2,000 Hz

400 Watts, low frequency

100 Watts, high frequency

0.775 Vrms (+0dBu)

10 Vrms (+22.2dBu)

XLR female, 22k Ohm, balanced, line-level input (unbalanced, 11k Ohm)

XLR male, wired in parallel with Input connector

HPR153F

42-19k Hz

38-20k Hz

133dB

90°x40°

11.1

12.9

15” (381mm) transducer with 3” (76mm) voice coil 6.5” (165mm) transducer with 1” (25mm) voice coil 1” (25mm) throat compression driver

500 and 2,000 Hz

400 Watts, low frequency

100 Watts, mid frequency

100 Watts, high frequency

0.775 Vrms (+0dBu)

10 Vrms (+22.2dBu)

XLR female, 22k Ohm, balanced, line-level input (unbalanced, 11k Ohm)

XLR male, wired in parallel with Input connector

Controls, Indicators, and Adjustments

Protection, Agency certs. AC Power Requirements

Gain control, 100 Hz low-cut filter switch, Front LED on/off switch, Limit/Clip (red LED), Signal presence (green LED), AC Power (blue LED), AC Power switch, AC circuit breaker

Thermal limiting, On/Off muting, power limiting, DC protection, short circuit protection, ultrasonic protection, RF protection, UL/CE listed

AC Power Connector and Cordset	Factory supplied IEC cordset: 6’ (2m) #18AWG 120V North American or European 230V cordset
Dimensions (height, width, depth)	32” (813mm) x 19” (485mm) x 18” (455mm)	45” (1137mm) x 19” (485mm) x 18” (455mm)
Installation Clearance	Allow for 6.0” (152mm) of free space behind the enclosure to assure proper amplifier cooling
Weight	100 lb/45.4 kg	118 lb/53.5 kg
Finish and Grill	Wear-resistant textured paint finish on plywood enclosure and powder-coated perforated steel grill

Notes:

1- Maximum Peak SPL: Calculated by adding the loudspeaker’s sensitivity (1W at 1m) to the peak power (dBw) of the amplifier provided.

2- Directivity Index (DI): Difference between on-axis SPL and average SPL (considering all axes) for the specified coverage range. DI= 10 log Q

3- Directivity Factor (Q): Directivity index expressed as a power ratio Q=10 exp DI/10

4- Amplifier Power: The maximum sustained power at less than 1% clipping, averaged over the intended frequency range,

5- Input Sensitivity: The sine-wave input voltage required to reach amplifier clipping, measured within the frequency range used to determine Maximum Peak SPL, with the gain on “normal” and no gain reduction due to limiting.

6- Input Headroom/Clipping: Maximum input voltage.

7- Input Connector/Impedance: RF shunt capacitance should not reduce impedance by more than 30% at 20k Hz.

QSC Audio HPR151W, HPR153F, HPR181W user manual Specifications, Full Range Models, HPR152F