AlarmSpace Saving Clock
I’ll Wake You Up in Style
CAUTION
INSTRUCCIONES IMPORTANTES DE SEGURIDAD
AC CONNECTION
User Guide
Please read these instructions completely before operating this product
memorex.com
MA4221
OPERATION (CONTINUED)
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO
TO QUALIFIED SERVICE PERSONNEL.
DANGEROUS VOLTAGE: The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
ATTENTION: The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
FCC WARNING: This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT AND FULLY INSERT.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there
1.Lea estas instrucciones.
2.Conserve estas instrucciones.
3.Preste atención a todas las advertencias.
4.Siga todas las instrucciones.
5.No utilice este aparato cerca de agua.
6.Limpie sólo con un paño seco.
7.No bloquee ninguna de las aberturas de ventilación. Instale el producto de acuerdo con las instrucciones del fabricante.
8.No instale el producto cerca de fuentes de calor, como radiadores, rejillas de calefacción, estufas u otros aparatos (incluidos los amplificadores) que generen calor.
9.No rechace el objetivo de seguridad del enchufe polarizado o de conexión a tierra. Un enchufe polarizado tiene dos clavijas: una más ancha que la otra. Un enchufe de conexión a tierra posee dos clavijas y una tercera prolongación de conexión a tierra. La clavija ancha y la tercera clavija se proporcionan para su seguridad. Si el enchufe proporcionado no encaja en su tomacorriente, comuníquese con un electricista para reemplazar el tomacorriente obsoleto.
10.Proteja el cable de alimentación de pisadas o pinchaduras, en particular en los enchufes, los tomacorrientes y el punto de donde salen del aparato.
11.Utilice sólo dispositivos/accesorios especificados por el fabricante.
12.Use sólo el carro, el pie, el trípode, el soporte o la mesa especificados por el fabricante o que se vendan con el aparato. Cuando se utilice un
carro, tenga cuidado al mover la combinación de carro y aparato para evitar lesiones por caídas.
13.Desconecte el aparato durante las tormentas eléctricas o cuando no se utilice durante un período prolongado.
14. El mantenimiento debe ser llevado a cabo por 
personal de mantenimiento calificado. Se requiere mantenimiento si el aparato se dañó de alguna forma; por ejemplo, si se derramó líquido o cayeron objetos dentro del aparato, si se expuso a la lluvia o a la humedad, si se cayó, si no funciona normalmente o si se dañó el cable de alimentación o el enchufe.
15.ADVERTENCIA: Para reducir el riesgo de incendio o descarga eléctrica, no exponga este aparato a la lluvia o a la humedad. No coloque objetos con líquidos (p. ej., jarrones) sobre el aparato.
16.El cable de alimentación de CA es el dispositivo para desconectar la corriente; por lo tanto, debe estar al alcance de la mano y se debe poder manejar durante el uso previsto. Para desconectar el aparato de la corriente, el cable de alimentación se debe quitar completamente del tomacorriente de CA.
17.PRECAUCIÓN: Para reducir el riesgo de incendio o explosión, no exponga las pilas a calor excesivo, como la luz solar directa, el fuego u otras fuentes de calor.
Insert the small end of the AC adapter into the DC IN 5V jack AO (located on the rear of the unit). Connect the other end to a wall outlet having 120V AC, 60 Hz.
NOTES:
•Remove both the DC plug and the
•Only use the supplied AC adapter which has the following specs: DC5V, 1.2A.
BATTERY INSTALLATION
Two “AAA” size batteries are used for time/alarm backup. Insert the batteries in this unit as follows:
1. | Open the Battery Compartment door AQ on the bottom of the unit by sliding in direction 1, then |
| 1 |
| lifting it off in direction 2. | 2 | |
2.Insert two (2) “AAA” batteries into the Battery Compartment as shown. Be sure to observe the
| polarity markings which are engraved inside the battery compartment. Alkaline batteries are | Front of unit |
| recommended for the longest playing time. | |
3. |
| |
Slide the Battery Compartment door back on. | AA A | |
NOTES: | AA A | |
• The AC adapter must be disconnected from the DC IN 5V jack in order for the unit to operate on |
| |
battery power.
• The battery icon will blink in the display when the batteries are low.
BATTERY PRECAUTIONS
Follow these precautions when using batteries in this device:
1. | Warning – Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. |
2. | Use only the size and type of batteries specified. |
3. | Be sure to follow the correct polarity when installing the batteries as indicated in the battery compartment. A reversed battery may cause damage to |
| the device. |
NOTES:
•If radio is selected, the last frequency will be tuned.
•You can also sync the alarm times from the app to this unit (see the
•If you select iPod, the iPod or iPhone device must be inserted and turned on.
To turn the alarm off:
To turn the alarm off, simply press the Alarm On/Off button AT. The alarm will turn off, but will remain set for the next day. To turn the alarm off so it will not sound the next day, press the Alarm On/Off button AT again so the alarm indicator disappears from the display. Snooze:
While the alarm is sounding, press the Snooze/Dimmer button W. The alarm will turn back on automatically ten minutes later. If desired, press the Snooze/Dimmer button W again for another ten minutes after the original Snooze time has been reached. You may repeat this process. To cancel the Snooze function, press the Alarm On/Off button AT.
Sleep:
With the unit on, press the Sleep button U; “SLEEP” will blink and “10” will show in the display, which indicates the unit will turn off after 10 minutes. Repeatedly press the Sleep button U to select the Sleep time, up to 90 minutes in 10 minute increments. After a couple seconds, the Sleep time will disappear from the display.
NOTE: To cancel the Sleep function, repeatedly press the Sleep button until “SLEEP” disappears from the display.
Line In Jack (Rear of Unit)
Insert one end of an audio cable (not included) into the LINE OUT jack on your external audio unit and the other end into the LINE IN jack AN on the rear of this unit. To listen to the external audio unit, turn this unit on using the Power button X, and turn on the external unit as well. Repeatedly press the SOURCE button V to select Line In mode;
Using an iPod or iPhone Device with this Unit
With an iPod or iPhone device connected, if this unit is not already on, turn this unit on by pressing the Power button X. Repeatedly press the Source button V to select iPod or iPhone device mode; “iPod” will appear in the display.
You can operate the iPod or iPhone device using its own controls, as per its owner’s manual, or you can use the controls on this
is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
•The rating information is located at the bottom of the apparatus.
SURGE PROTECTORS: It is recommended to use a surge protector for AC connection. Lightning and power surges ARE NOT covered under warranty for
MISE EN GARDE
RISQUE DE CHOC ÉLECTRIQUE NE
PAS OUVRIR
MISE EN GARDE : POUR RÉDUIRE LES RISQUES DE CHOC ÉLECTRIQUE, NE PAS RETIRER LE COUVERCLE (OU L’ARRIÈRE). AUCUNE PIÈCE À L’INTÉRIEUR NE PEUT ÊTRE RÉPARÉE PAR L’UTILISATEUR. CONFIEZ TOUTE RÉPARATION À UN TECHNICIEN QUALIFIÉ.
4. | Do not mix different types of batteries together (e.g. Alkaline, Rechargeable and |
5. | If the device is not to be used for a long period of time, remove the batteries to prevent damage or injury from possible battery leakage. |
6. | Do not try to recharge a battery not intended to be recharged; it can overheat and rupture. (Follow battery manufacturer’s directions.) |
7. | Remove batteries promptly if consumed. |
8. | Clean the battery contacts and also those of the device prior to battery installation. |
LOCATION OF CONTROLS
unit to operate the iPod or iPhone device.
To play/pause the iPod or iPhone device:
Press the Play/Pause4;button X to start playback on your iPod or iPhone device. Press again to pause playback, the Pause indicator will blink in the display; press yet again to resume playback. If you have the Shuffle and/or the Repeat option selected on your iPod or iPhone device, the respective indicator will appear in this display.
To skip forward or backward on the iPod device: Press the Tune/Skip/Search 9 U or : W button to skip to the beginning of the current track, previous or next track.
To search forward or backward on the iPod device: Press and hold the Tune/Skip/Search 9 U or : W button to
this product.
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
This Class B digital apparatus complies with Canadian
IMPORTANT SAFETY INSTRUCTIONS
TENSION DANGEREUSE : L’éclair avec le symbole de la pointe de flèche dans un triangle équilatéral est destiné à alerter l’utilisateur de la présence de tension dangereuse non isolée dans le boîtier du produit. Elle peut être suffisamment importante pour constituer un risque de décharge électrique pour les personnes à proximité.
ATTENTION : Le point d’exclamation dans un triangle équilatéral est destiné à alerter l’utilisateur de la nécessité de respecter les consignes d’utilisation et de maintenance (réparation) fournies dans la documentation qui accompagne l’appareil.
1
2
3
4
8
9
10
1. | Tune/Skip/Search 9 Button |
2. | Source Button |
3. | Snooze/Dimmer Button |
4. | Play/Pause4;Button |
5. | iPod or iPhone Device Dock |
| with Connector |
6. | Sleep Button |
search within the
To adjust the main volume: Press the Volume + AL or – V button to increase or decrease the volume.
To turn the unit off: To turn this unit off, press the Power button X.
NOTE: After you have adjusted the volume setting, if you turn the unit off and then on again, the volume level will be set to the level you selected prior to turning the unit off.
Using the FM Radio
It is highly recommended to install the Memorex FM Radio + Alarm Clock App so you can set FM presets, view the frequencies, and more. See the
Turn this unit on by pressing the Power button X.
1.Read these Instructions.
2.Keep these Instructions.
3.Heed all Warnings.
4.Follow all Instructions.
5.Do not use this apparatus near water.
6.Clean only with a dry cloth.
7.Do not block any of the ventilation openings. Install in accordance with the manufacturer’s instructions.
8.Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
9.Do not defeat the safety purpose of the polarized or
10.Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
11.Only use attachments/accessories specified by the manufacturer.
12.Use only with a cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/ apparatus combination to avoid injury from
13. Unplug this apparatus during lightning storms or
when unused for long periods of time. 14. Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been damaged in any way, such as
cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
15.WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. Do not place objects filled with water, such as a vase, on the apparatus.
16.The AC mains plug is used as the power disconnect device and it should remain readily accessible and operable during intended use. In order to completely disconnect the apparatus from power, the mains plug should be completely removed from the AC outlet socket.
17.CAUTION: To reduce the risk of fire or explosion, do not expose batteries to excessive heat such as sunshine, fire or other heat sources.
AVERTISSEMENT DE LA FCC : CET APPAREIL PEUT GÉNÉRER OU UTILISER DE L’ÉNERGIE DE RADIOFRÉQUENCE. TOUT CHANGEMENT OU MODIFICATION DE CET APPAREIL PEUT ENTRAÎNER DES INTERFÉRENCES NUISIBLES À MOINS QUE LES MODIFICATIONS NE SOIENT EXPRESSÉMENT APPROUVÉES DANS LE GUIDE D’UTILISATION. L’UTILISATEUR RISQUE LE RETRAIT DE L’AUTORISATION D’UTILISER CET ÉQUIPEMENT SI UNE MODIFICATION OU UN CHANGEMENT NON AUTORISÉ EST EFFECTUÉ.
MISE EN GARDE : POUR ÉVITER TOUT RISQUE DE CHOC ÉLECTRIQUE, INSÉREZ À FOND LA LAME LA PLUS LARGE DANS L’ORIFICE LE PLUS LARGE DE LA PRISE.
CET APPAREIL EST CONFORME À LA SECTION 15 DES RÈGLEMENTS DE LA FCC. LE FONCTIONNEMENT EST SOUMIS AUX DEUX CONDITIONS SUIVANTES
:(1) CE DISPOSITIF N’EST PAS CENSÉ CAUSER D’INTERFÉRENCES NUISIBLES, ET (2) CE DISPOSITIF DOIT RECEVOIR TOUTE INTERFÉRENCE, Y COMPRIS
CELLES POUVANT CAUSER UN FONCTIONNEMENT NON DÉSIRÉ.
REMARQUE : Cet appareil a été testé et approuvé comme étant conforme aux limites préconisées pour un appareil numérique de la classe B conformément à la section 15 des réglementations de la FCC. Ces limites sont conçues pour fournir une bonne protection contre les interférences nuisibles dans une installation domestique. Cet appareil génère, utilise et peut émettre de l’énergie de radiofréquence et, s’il n’est pas installé et utilisé conformément aux instructions, peut perturber les communications radio. Cependant, il n’existe aucune garantie quant à l’absence d’interférences dans une installation particulière. Si cet appareil cause des interférences nuisibles au niveau de la réception radio ou de la télévision, (ce qui peut être vérifié en l’allumant et en l’éteignant), l’utilisateur doit essayer de remédier au problème en prenant les mesures suivantes :
5
6
7
11
12
13
7. | Volume – (Down) Button |
8. | Tune/Skip/Search : Button |
9. | Power Button |
10. | Alarm On/Off Button |
11. | Set Time/Sync Button |
12. | Volume + (Up) Button |
13. | Display |
14. | Line IN Jack |
15. | DC IN 5V Jack (AC ADAPTER PART |
| NO. |
16. FM Antenna | |
17. | Battery Compartment (Bottom of unit) |
| (BATTERY COVER PART NO. |
Repeatedly press the Source button V to select Radio mode; “radio” will appear in the display.
Repeatedly press the Tune/Skip/Search 9 U or : W button to manually advance the frequency up or down until the desired frequency is playing.
For auto tuning, press and hold the Tune/Skip/Search 9 U or : W button until the frequency starts to scan, then release; the tuner will search and then stop on the next strong station it finds. Repeat this step until the desired frequency appears in the display.
To adjust the main volume: Press the Volume + AL or – V button to increase or decrease the volume.
To turn the unit off: To turn this unit off, press the Power button X. To change the FM region:
This unit allows you to set the desired radio region. For region details, see Radio Regions below.
•With the unit off, press and hold the Source V and Play/Pause4;X buttons simultaneously until the region number appears in the display.
•Within four seconds, select a region using the Tune/Skip/Search 9 U or : W button.
•When done setting, press any button or wait for five seconds; the region will be set.
RADIO REGIONS: Region 1 – United States (87.5MHz to 108MHz)
Region 2 – Europe (87.5MHz to 108MHz)
Region 3 – Japan (76MHz to 108MHz)
Dimmer: Press the Snooze/Dimmer button W to dim the display.
PRECAUCIÓN
RIESGO DE DESCARGA ELÉCTRICA
NO ABRIR
PRECAUCIÓN: PARA REDUCIR EL RIESGO DE DESCARGA ELÉCTRICA, NO QUITE LA CUBIERTA (NI LA PARTE TRASERA). NO CONTIENE PIEZAS EN EL INTERIOR QUE PUEDAN SER REPARADAS POR EL USUARIO. EL MANTENIMIENTO DEBE SER REALIZADO POR PERSONAL DE MANTENIMIENTO CALIFICADO.
VOLTAJE PELIGROSO: El rayo con el símbolo de la punta de flecha dentro de un triángulo equilátero tiene como objetivo advertir al usuario acerca de la presencia de voltaje no aislado peligroso dentro de la caja del producto que puede ser de magnitud suficiente para generar un riesgo de descarga eléctrica para las personas.
ATENCIÓN: El signo de exclamación dentro de un triángulo equilátero tiene como objetivo alertar al usuario acerca de la presencia de instrucciones de funcionamiento y mantenimiento (servicio) importantes en la bibliografía que acompaña a la aplicación.
•Réorientez ou repositionnez l’antenne réceptrice.
•Augmentez la distance qui sépare l’appareil du récepteur.
•Connectez l’appareil à une prise sur un circuit différent de celui utilisé par le récepteur.
•Consultez le revendeur ou un technicien radio/téléviseur expérimenté.
•La plaque signalétique est apposée sous l’appareil.
PARASURTENSEURS : IL EST RECOMMANDÉ D’UTILISER UN PARASURTENSEUR POUR LE BRANCHEMENT SUR COURANT ALTERNATIF. LES DÉGÂTS DUS À LA FOUDRE ET AUX SURTENSIONS NE SONT PAS COUVERTS PAR LA GARANTIE QUI ACCOMPAGNE CE PRODUIT.
AVERTISSEMENT : POUR ÉVITER TOUT RISQUE D’INCENDIE OU DE DÉCHARGE ÉLECTRIQUE, N’EXPOSEZ PAS CET APPAREIL
À LA PLUIE OU À L’HUMIDITÉ.
Cet appareil numérique de la classe B est conforme à la norme
14
15
16
17
*Consumer Replaceable Part (See end of guide to order.)
When first connected to an
NOTE: App requires iOS 4.0 or greater. To use the App:
The default display is the Alarms screen. Here you can turn the alarms on or off, set Alarm 1 and/or Alarm 2, and set the source, volume and snooze time. Press Sync to sync the alarms on the iPod or iPhone device with this unit.
Settings: Press the Settings icon to bring up the Settings display. Here you can sync clock time, toggle 12/24 hour mode, set display brightness, and set the Sleep timer.
About: Press the About icon to view the About display, which will give you information about your unit and the latest version installed.
Audio: Press the Audio icon to bring up the Audio display. Here you can select iPod, FM, AUX or OFF. The FM function is in sync with this unit’s FM radio and buttons. Therefore, after selecting FM you can drag the frequency on the iPod or iPhone device to the left or right to select a frequency, or you can use this unit’s controls for the same results.
ADVERTENCIA DE LA FCC: ESTE EQUIPO PUEDE GENERAR O UTILIZAR ENERGÍA DE RADIO FRECUENCIA. LOS CAMBIOS O LAS MODIFICACIONES DE ESTE EQUIPO PUEDEN PROVOCAR INTERFERENCIA PERJUDICIAL, A MENOS QUE ESTÉN EXPRESAMENTE APROBADAS EN EL MANUAL DE INSTRUCCIONES. EL USUARIO PODRÍA PERDER LA AUTORIDAD PARA HACER FUNCIONAR ESTE EQUIPO SI REALIZA ALGÚN CAMBIO O MODIFICACIÓN NO AUTORIZADOS.
IMPORTANTES CONSIGNES DE SÉCURITÉ
OPERATION
To set or reset the actual time:
It is highly recommended to install the Memorex FM Radio + Alarm Clock App to utilize its capabilities. See the
Regardless of the source, or if the power is on or off, you can set the time as follows:
To make a preset of a frequency, simply press and hold one of the six presets until the iPod or iPhone device vibrates to memorize the station. To recall, simply press the preset.
Note: The App is subject to change without notice and is not compatible with all iPod devices.
PRECAUCIÓN: PARA EVITAR DESCARGAS ELÉCTRICAS, UNA LA CLAVIJA ANCHA DEL ENCHUFE CON LA RANURA ANCHA E INSÉRTELA POR COMPLETO.
ESTE DISPOSITIVO CUMPLE CON LA PARTE 15 DE LAS REGLAS DE LA FCC (FEDERAL COMUNICATIONS COMMISSION). EL FUNCIONAMIENTO DEPENDE DE
LAS DOS CONDICIONES QUE SE MENCIONAN A CONTINUACIÓN: (1) ESTE DISPOSITIVO NO CAUSA INTERFERENCIA NOCIVA Y (2) ESTE DISPOSITIVO DEBE ACEPTAR TODA INTERFERENCIA RECIBIDA, INCLUYENDO INTERFERENCIA QUE PUEDA OCASIONAR UN FUNCIONAMIENTO INDESEABLE.
NOTA: Este equipo ha sido probado y cumple con los límites correspondientes a un dispositivo digital Clase B, según la parte 15 de las Normas de FCC. Estos límites están diseñados para proporcionar una protección razonable contra la interferencia dañina en una instalación residencial. Este equipo genera, utiliza y puede irradiar energía de radiofrecuencia y, si no se instala y usa de acuerdo con las instrucciones, puede generar interferencia perjudicial en
las comunicaciones de radio. Sin embargo, no se garantiza que la interferencia no se produzca en una instalación en particular. Si este equipo genera interferencia perjudicial en la recepción de radio o televisión, que puede determinarse encendiendo y apagando el equipo, se recomienda al usuario que intente corregir la interferencia mediante una o más de las siguientes medidas:
•Vuelva a orientar o ubicar la antena receptora.
•Aumente la separación entre el equipo y el receptor.
•Conecte el equipo a un tomacorriente de un circuito distinto del que está conectado el receptor.
•Consulte con el distribuidor o con un técnico de radio o TV experimentado para obtener asistencia.
•La información de clasificación se encuentra en la parte inferior del aparato
PROTECTORES CONTRA SOBRETENSIÓN: SE RECOMIENDA UTILIZAR UN PROTECTOR CONTRA SOBRETENSIÓN PARA LA CONEXIÓN DE CA. LOS CASOS
DE SOBRETENSIÓN DE ENERGÍA Y RAYOS NO ESTÁN CUBIERTOS POR LA GARANTÍA DE ESTE PRODUCTO.
ADVERTENCIA: PARA EVITAR EL RIESGO DE INCENDIO O DESCARGA, NO EXPONGA ESTA UNIDAD A LA LLUVIA O LA HUMEDAD.
Este aparato digital Clase B cumple con la norma canadiense
Lisez ces consignes.
2.Conservez ces consignes.
3.Tenez compte de tous les avertissements.
4.Suivez toutes les consignes.
5.N’utilisez pas cet appareil à proximité de l’eau.
6.Nettoyez uniquement avec un chiffon sec.
7.Ne bouchez pas les orifices prévus pour la ventilation. Installez conformément aux instructions du fabricant.
8.N’installez pas l’appareil à proximité de sources de chaleur telles que les radiateurs, les grilles de chauffage, les cuisinières ou d’autres appareils (y compris les amplificateurs) qui génèrent de la chaleur.
9.Ne supprimez en aucun cas la fonctionnalité de sécurité de la fiche polarisée ou avec mise à la terre. Une fiche polarisée comporte deux lames avec une plus large que l’autre. Une fiche avec mise à la terre a deux lames et une troisième broche de mise à la terre. La lame large ou la troisième broche ont été prévues pour votre sécurité. Si vous ne parvenez pas à brancher la fiche fournie dans votre prise, consultez un électricien afin qu’il remplace la prise obsolète.
10.Protégez le cordon d’alimentation pour qu’il ne soit pas piétiné ou pincé en particulier au niveau des fiches, des prises de courant et à l’endroit où il sort de l’appareil.
11.Utilisez uniquement les fixations ou les accessoires recommandés par le fabricant.
12.Utilisez uniquement avec un chariot, un pied, un trépied, un support ou une table recommandé(e) par le fabricant ou vendu(e) avec l’appareil. Si un chariot est utilisé, déplacez prudemment l’ensemble
appareil et chariot pour éviter des blessures causées par un basculement.
13. Débranchez cet appareil pendant les orages ou si vous prévoyez de ne pas l’utiliser pendant
une longue période. 14. Confiez toute réparation à du personnel
qualifié. Une réparation est nécessaire si l’appareil a été endommagé de quelconque
manière, par ex. si le câble ou la fiche d’alimentation est abîmé(e), ou du liquide a été renversé ou si des objets sont tombés dans l’appareil, ou encore si ce dernier a été exposé à la pluie ou à l’humidité, ne fonctionne pas normalement, ou est tombé.
15.AVERTISSEMENT: Pour réduire le risque d’incendie ou de choc électrique, n’exposez pas cet appareil à la pluie ni à l’humidité. Aucun objet contenant du liquide, comme un vase, ne doit être posé sur l’appareil.
16.La fiche secteur est utilisée comme dispositif de mise hors tension et doit rester aisément accessible et fonctionnelle à tout moment pendant l’utilisation prévue. Pour mettre l’appareil totalement hors tension, retirez complètement la fiche de la prise secteur.
17.MISE EN GARDE : Pour réduire le risque d’incendie ou d’explosion, n’exposez pas les piles à une chaleur intense, par exemple au soleil, au feu ou à d’autres sources
de chaleur.
1.Press and hold the Set Time/Sync button AK until the AM/PM indicator blinks.
2.Set the unit to standard 12 hour time or 24 hour (military) time using the Tune/Skip/Search 9 U or : W button. Then press the Set Time/Sync button AK again; the hours will blink.
3.Set the current hour using the Tune/Skip/Search 9 U or : W button. Then press the Set Time/Sync button again AK; the minutes will blink.
4.Set the current minutes using the Tune/Skip/Search 9 U or : W button. Then press the Set Time/Sync button again AK;
the time will be set.
To sync the iPod® or iPhone® device’s time to this unit’s time:
With the power on, connect an iPod or Phone device as shown later in this manual. Press the Set Time/Sync button AK until the current time appears and the display blinks twice. The time will then be synced.
NOTES:
•The Set Time/Sync button will not set the alarm.
•The iPod mini, iPod photo and iPod 4th generation do not support the SYNC function.
To set the alarm:
Regardless of the source, or if the power is on or off, you can set the alarm times as follows:
1.Press and hold the Alarm On/Off button AT until the alarm time blinks.
2.Set the alarm hour using the Tune/Skip/Search 9 U or : W button. Then press the Alarm On/Off button AT again; the alarm minutes will blink.
3.Set the alarm minutes using the Tune/Skip/Search 9 U or : W button. Then press the Alarm On/Off button AT again; the source icon will blink.
4.Set the desired source to wake to (iPod, Radio or Buzzer) using the Tune/Skip/Search 9 U or : W button. Then press the Alarm On/Off button AT again; the volume level will blink.
5.Set the volume using the Volume + AL or – V button. Then press the Alarm On/Off button AT again and the alarm will be set. The alarm icon will appear in the display to indicate it is activated.
SPECIFICATIONS AND COMPATIBILITY
GENERAL: |
|
|
|
Power Source | DC 5V, 1.2A Adapter (Center Positive) | Output Power | 1 x 0.8W |
Speaker | 1 x 4 ohm | Weight | 0.96 lbs |
Dimensions | 4.45 (W) x 3.30 (D) x 6.97 (H) inches | Specifications are subject to change without notice. |
|
Made for iPod touch (2nd, 3rd and 4th generation), iPod classic, iPod nano (2nd, 3rd, 4th, 5th and
6th generation), iPhone 4S, iPhone 4, iPhone 3GS and iPhone 3G.
“Made for iPod” and “Made for iPhone” mean that an electronic accessory has been designed to connect specifically to iPod or iPhone, respectively, and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards. Please note that the use of this accessory with iPod or iPhone may affect wireless performance.
iPhone, iPod, iPod classic, iPod nano and iPod touch are trademarks of Apple Inc., registered in the U.S. and other countries.
Imation Enterprises Corp.
1 Imation Way, Oakdale, MN
Memorex and the Memorex logo are trademarks of Imation Corp and its affiliates. All other trademarks are the property of their respective owners.
For additional setup, operating assistance or an electronic version of this user manual, please visit www.memorex.com
For consumer replaceable part(s), verify part number(s) then contact our parts and accessory fulfillment center at: