CDJ-210
the track selection rotary to scan to the first track to be placed in the set list. When you have selected the proper track press PGM and the
11BRAKE: To engage the BRAKE function, press the BRAKE button until it illuminates. Press the PLAY/ PAUSE button to perform the brake effect. To restart the song, press the PLAY/ PAUSE button.
12REVERSE: When the REVERSE button is pressed, the file that is currently playing begins to play in reverse mode.
13SINGLE: Pressing the SINGLE button engages SINGLE mode, in this mode the
(after the last track, the unit will return to the first track of the disc and continue to play).
14TIME: The TIME button switches the time display between three available sources, these three are TIME ELAPSED on the track, TOTAL REMAIN and REMAIN. ELAPSED indi- cates how much time has currently gone by since the play button was pressed, TOTAL REMAIN will count down the time remaining on the entire disc and REMAIN counts down the time that is left before the end of the track.
NOTE: TOTAL REMAIN WILL NOT SHOW FOR MP3 FILES.
15PITCH: Pushing and holding the PITCH button activates the PITCH CONTROL SLIDE. You can then select which PITCH percent you want by pressing the PITCH button and choos- ing 4%, 8% and 16% depending on which LED is illuminated. Push and hold the PITCH button again to deactivate this mode.
16PITCH CONTROL SLIDE: Moving the PITCH CONTROL SLIDE up or down will lower or raise the pitch percentage up to +/- 4, 8, or 16%.
17PITCH BEND: Pushing the PITCH BEND BUTTONS will au- tomatically raise the pitch up to +16% or lower the pitch down to
18LOOP SECTION: A LOOP repeats the section between the entry point (IN) and the exit point (OUT).
A.To set a loop while the unit is playing, start by pressing the IN BUTTON (it will light up)
B.When you reach the desired end loop point press the OUT BUTTON (it will also light up). The loop will continue playing until you press the OUT BUTTON again allowing the music to continue from that point on.
C.To
D.When you have released your loop the OUT BUTTON will turn OFF and the IN BUTTON will remain lit to indicate that your loop is stored in the
E.Pressing the IN BUTTON again while the unit is playing will erase the previously saved loop while saving your new loop entry point.
F.Press OUT to exit the loop and save a new complete loop.
G.Press RELOOP to return to the beginning of the previ- ously saved loop from normal play. Press RELOOP repeat- edly to cause the loop to stutter.
NOTE: THE FIRST LOOP WILL HAVE A PAUSE AT THE EXIT POINT, WHILE ALL OTHERS WILL BE SEAMLESS.
19PLAY / PAUSE: Each press of the PLAY / PAUSE BUTTON causes the operation to change from PLAY to PAUSE or from PAUSE back to PLAY. The PLAY/PAUSE BUTTON remains lit when in PLAY mode, while it blinks in PAUSE mode.
20CUE: To set a CUE point, press the PLAY/PAUSE BUTTON while a file is playing and use the JOG WHEEL to locate a desired CUE point. Pressing the PLAY/PAUSE BUTTON again will set a CUE point. While the unit is playing and after the cue point has been programmed, pressing CUE will cause the CD player to enter the PAUSE mode (PLAY/PAUSE BUTTON blinks) at the programmed cue point (the CUE LED is lit). Hold- ing down the CUE button changes the function to preview, and allows you to stutter start or play from the programmed CUE POINT. Releasing the CUE button will return the CD to the preset CUE POINT.
21SEARCH: The SEARCH buttons are used to fast forward and rewind within a track.
22TRACK SELECTION ROTARY: The TRACK SELECTION RO- TARY allows you to select the next or previous track by either turning it clockwise to go forward or
TION ROTARY.
NOTE: ONCE YOU HAVE SKIPPED TO ANOTHER TRACK, YOU MAY NOT GO BACK TO YOUR PROGRAMMED CUE POINT. YOU MUST BEGIN YOUR CUE SELECTION OVER AGAIN, THE CUE WILL BE PRESET TO THE BEGINNING OF THE NEWLY SELECTED TRACK.
TROUBLESHOOTING:
- If a disc will not play, check to see if the disc was loaded cor- rectly (label side up). Also check the disc for excessive dirt, scratches, etc.
- If the disc turns but there is no sound, check the cable con- nections, if they are ok, check your amplifier or receiver.
5