Philips EXP2460/02 user manual Power Supply, General Information

EnglishCONTROLS

Supplied Accessories:

1 x headphones AY3806

1 x AC/DC adapter AY3162 (not for all versions)

CONTROLS ( see figure 1)

1...........................display

2	2;	switches the player on, starts playback and pauses playback.
3 ESP		selects between the battery powersave mode and
		Electronic Skip Protection (ESP). ESP prevents playback
		interruptions caused by shocks.
4 PROG		programs tracks and reviews the program.
5 MODE		selects playback options (e.g. SHUFFLE, REPEAT).
6 DBB		switches the bass enhancement on and off. This button also
		switches acoustic feedback (the beep) on/off when it is
		pressed for more than 2 seconds
7	9	stops playback/clears programmed tracks/ switches off the
		set.
8	∞ /§	skips and searches tracks backward/forward.
	3 /4	MP3 only: skips forward/backward albums.

9OPEN 2 .............opens the CD lid.

0p / LINE OUT....3.5mm headphone jack;

jack to connect the player to another audio input of an additional appliance.

!VOL - / +............adjusts the volume.

@ OFF	switches HOLD off.
RESUME	stores the last position of a CD track played
HOLD	locks all buttons.
# 4.5V DC	jack for external power supply.

POWER SUPPLY

Batteries (not included)

Inserting AA (LR6, UM3) batteries

1 Open the battery compartment.

2 Insert 2 x AA batteries as shown into the battery compartment.

3 Close the battery compartment.

Helpful Hints:

–Old and new or different types of batteries should not be combined.

–Remove batteries if they are empty or if the player is not going to be used for a long time.

Battery indication

The approximate power level of your batteries is shown in the display. Battery full

Battery two-thirds full

Battery one-third full

Battery dead or empty.When the batteries are dead or empty, the symbol A flashes, rP bAtt is displayed, and the beep tone sounds repeatedly.

Batteries contain chemical substances, so they should be disposed of properly.

The type plate is located on the bottom of the set.

POWER SUPPLY

Power adapter (supplied or optionally available)

Only use AY3162 adapter (4.5V/450mA DC, positive pole to the center pin). Any other product may damage the player.

1 Make sure local voltage corresponds to the power adapter's voltage.

2Connect the power adapter to the 4.5V DC socket of the player and to the wall socket.

Helpful Hints:

–Always disconnect the adapter when you are not using it.

GENERAL INFORMATION

CD player and CD handling

• Do not touch the lens A of the CD player.

• Do not expose the unit, batteries or CDs to humidi- ty, rain, sand or excessive heat (caused by heating equipment or direct sunlight).

• You can clean the CD player with soft, slightly dampened, lint-free cloth. Do not use any cleaning agent as it may have a corrosive effect.

•To clean the CD, wipe it in a straight line from the center toward the edge using soft, lint-free cloth. The cleaning agent may damage the disc! Never write on a CD or attach a sticker to it.

•The lens may cloud over when the unit is moved suddenly from cold to warm surroundings. In that case, playing a CD is not possible. Leave the CD player in a warm environment until the moisture has evaporated.

•Active mobile phones in the vicinity of the CD player may cause malfunctions.

•Avoid dropping the unit as this may cause damage.

GENERAL INFORMATION

ENVIRONMENTAL INFORMATION

•All redundant packing material has been omitted. We have done our utmost to make the packaging easily separable into two mono materials: cardboard (box) and polyethylene (bags, protective foam sheet).

•Your set consists of materials which can be recycled if disassembled by a spe- cialized company. Please observe the local regulations regarding the disposal of packing materials, dead batteries and old equipment.

This set complies with the radio interference requirements of the

European Union.

–Apparatus shall not be exposed to dripping or splashing.

–Do not place any sources of danger on the apparatus (e.g. liquid filled objects, lighted candles)