English | CONTROLS |
BASIC FUNCTIONS
DIGITAL TUNER
TOP AND FRONT PANELS
(See 1)
1SOURCE – selects CD/ TUNER / TAPE function
2y – power on/ off switch
3Display – shows the status of the set
4Cassette recorder keys RECORD 0 – starts recording PLAY 2 – starts playback
SEARCH 5/6 – fast winds/rewinds tape STOP/OPEN 9/
–opens the cassette compartment
–stops the tape
PAUSE ; – pauses playback or recording
5BASS, MID, HIGH – EQ keys to adjust the bass, mid & treble frequencies
6PROG
CD: programs tracks and reviews the program;
Tuner: programs preset radio stations
Navigation controls 7∞, §
CD: – searches back and forward within a track;
–skips to the beginning of a current track/previous/ later track
Tuner: – tunes to radio stations (down, up).
82; – starts or pauses CD playback
99 – stops CD playback;
– erases a CD program
0MODE – selects different play modes: e.g. REPEAT or SHUFFLE (random) order
!PUSH TO OPEN – opens/closes the CD door @VOLUME – to adjust volume level
#REMOTE SENSOR (for AZ2055 model only) – infrared sensor for remote control
$PRESET DOWN/ UP
%BAND – selects waveband
^DBB – (Dynamic Bass Boost) activates a more vivid bass response
BACK PANEL
&Telescopic antenna – improves FM reception
*Battery compartment – for 6 batteries, type
(p – 3.5 mm stereo headphone jack Note: The speakers will be muted when headphones are connected to the set.
)AC MAINS – inlet for power cord
REMOTE CONTROL (for AZ2055 only)
1VOLUME 3,4 – adjusts volume level (up, down) 2SHUFFLE – plays all CD tracks in random order 32; – starts/ pauses CD playback
4SEARCH 5, 6 – searches backwards/ forwards within a track
5PRESET +, – – selects a preset radio station (up, down)
6TUNING ∞, § – tunes to tuner stations (down, up)
79 – stops CD playback;
– erases a CD program
8¡, ™ – skips to the beginning of a current track previous/ subsequent track
9REPEAT – repeats a track /program/ entire CD
CAUTION
Use of controls or adjustments or performance of procedures other than herein may result in hazardous radiation exposure or other unsafe operation.
POWER SUPPLY
Whenever convenient, use the power supply to conserve battery life. Make sure you remove the power plug from the set and wall outlet before inserting batteries.
Batteries (not included)
•Insert 6 batteries, type
Remote control (for AZ2055 only /See A)
•Insert 2 batteries, type AAA, R03 or UM4 (preferably alkaline).
Incorrect use of batteries can cause electrolyte leakage and will corrode the compartment or cause the batteries to burst.
•Do not mix battery types: e.g. alkaline with carbon zinc. Only use batteries of the same type for the set.
•When inserting new batteries, do not try to mix old batteries with the new ones.
•Batteries contain chemical substances, so they should be disposed of properly.
Using AC Power
1Check if the power supply, as shown on the type plate located on the bottom of the set, corresponds to your local power supply. If it does not, consult your dealer or service center.
2If your set is equipped with a voltage selector, adjust the selector so that it matches with the local power .
3Connect the power cord to the wall outlet.
4To disconnect the power supply, unplug the set from the wall outlet.
Auto-Standby mode
When a CD or tape has reached the end of playback and remains in the stop position for more than
15 minutes, the set will switch off automatically to save energy.
The type plate is located on the bottom of the set.
BASIC FUNCTIONS
Switching on and off and selecting function
1Press y on the set to switch on.
2Press SOURCE once or more to select: CD, TUNER or TAPE function.
3Press y to switch off the set.
Notes:
–To change from TAPE to TUNER or CD function, or when you are switching off the set: first, make sure you press the tape STOP 9 key to end playback and all the cassette keys are released.
–The tone, sound settings, tuner presets and the volume level (up to a maximum volume level of 20) will be retained in the set’s memory.
Adjusting volume and sound
1Adjust the volume with the VOLUME control.
™Display shows the volume level and a number from
2Press DBB once or more to select dynamic bass boost on or off.
™Display: shows 
when activated.
3To adjust the bass, mid and treble tones, press and hold + or – on the BASS, MID, HIGH keys until you reach the desired level,
™Display briefly shows BASS, MID, or HIGH and the level. (See 3)
Note: To prevent sound interference the bass control options operate exclusively. You cannot combine the bass from BASS with DBB
™The display shows 
or the 
indicator is automatically switched off to remind you if you attempt to use both bass settings.