Philips AZ1830 user manual Power Supply

English Controls / Power Suppy

Power Supply

Supplied accessories

–AC power cord

–Remote control

Top and front panels (See 1)

1Source selector: CD/USB,TUNER, OFF

–selects CD/MP3-CD (or USB mode), or radio

–switches off the set

2VOLUME – adjusts volume level

3LIFT TO OPEN – lifts here to open the disc door

4ALBUM+/-

– For MP3-CD/ USB play: select albums

59 – stops disc/USB playback;

–erases a program

6iR – infrared sensor for remote control

7Display – shows disc/USB play functions

8DBB – turns the bass enhancement on/off.

9MODE – selects different play modes: e.g. REPEAT or SHUFFLE (random order)

0PROG – programs tracks and reviews the program

!USB port – connects an external USB mass storage device

@CD/USB – enters disc or USB mode

#BAND – selects wavebands, MW or FM

$Frequency indicator – shows the radio fre- quency of your selected waveband

%TUNING – tunes to radio stations

^ ∞ §

–For disc/ USB play:

–skips to the beginning of a current/ previous/ later track

–fast searches backwards and forwards with- in a track

&2; – starts or pauses disc/USB playback

Back panel (See 1)

*Telescopic antenna – improves FM reception

(Battery door – open to insert 6 x 1.5V R-14/ UM2/ C-cells

)AC~ MAINS – inlet for power cord

Remote control (See 1)

1MODE – selects different play modes: e.g. REPEAT or SHUFFLE (random order)

2PROG – programs tracks and reviews the program

3 9 – stops disc/USB playback;

– erases a program

4 2; – starts/ pauses CD/USB playback

5 ∞ §

For disc/ USB play:

–fast searches back and forward

–skips to the beginning of a current track/ previous/ later track

6ALBUM +/-

For MP3-CD/USB play: selects albums

Power Supply

Whenever convenient, use the power supply cord if you want to conserve battery life. Make sure you remove the plug from the set and wall outlet before inserting batteries.

Batteries

Main set (See 1)

•Insert 6 batteries, type R-14, UM2 or C- cells (not included, preferably alkaline) with the correct polarity.

Remote control (See 1)

Important!

•Before using the remote control, remove the insulation plastic tab as shown

in figure 0.

•If the remote control does not function correctly or the operating range is reduced, replace the battery with a new (CR2025) type battery

1Press and hold the latch (A) in the direction as shown in figure 0.

2Simultaneously, pull the battery tray (B) out.

3Replace a new battery, and fully insert the battery tray back to the original position.

•Incorrect use of batteries can cause elec- trolyte leakage and will corrode the compart- ment or cause the batteries to burst:

•Do not mix battery types: e.g. alkaline with carbon zinc. Only use batteries of the same type for the set.

•When inserting new batteries, do not try to mix old batteries with the new ones.

•Remove the batteries if the set is not to be used for a long time.

Batteries contain chemical substances, so they should be disposed of properly.

Using AC power

1Check if the power/mains voltage, as shown on the type plate located on the bottom of the set, corresponds to your local power supply. If it does not, consult your dealer or service center.

2Connect the power cord to the

AC~ MAINS inlet and the wall socket.The set is now ready for use.

3To switch the set off completely, withdraw the power cord from the wall socket.

4Install the unit near the AC outlet and where the AC power plug can be easily reached.

•Disconnect the power cord from the wall socket to protect your set during heavy thun- derstorms. Children could seriously injure themselves as the free end of the cable may still be live if only the connector is removed from the MAINS socket at the back of the unit.

The type plate is located on the bottom of the set.

Auto power saving

•When the source selector is adjusted to CD/USB and the set is in the PAUSE posi- tion for 5 minutes, the set will be auto switched to the stop position to save power.

•When the source selector is adjusted to CD/USB and the set is in the STOP position for 15 minutes, the set will be auto switched to sleep (standby )mode.To wake it up, press 2;.

Helpful hints:

–To avoid unnecessary energy consumption, always adjust the source selector to OFF after using the set.

CAUTION

-Visible and invisible laser radiation. If the cover is open, do not look at the beam.

-High voltage! Do not open.You run the risk of getting an electric shock. The machine does not contain any user-serviceable parts.

-Modification of the product could result in hazardous radiation of EMC or other unsafe operation.