Haier AD422BMBAA manual Remove the upper cover of wire controller, Install wire controller

Page 28

Installation procedure

Install wire controller

 

 

 

1.Remove the upper cover of wire controller

The PC board is installed on the back cover of wire controller. When remove the upper cover, pay attention not to damage PC board.

Upper cover of wire controller

Back cover of wire controller

Switch

Screw hole

2.Install wire controller

Drill 2 wall holes according to the position of the 2 screw holes on the back cover of wire controller, then hit wood in the wall holes. Put the 2 screw h- oles on the back cover of wire controller properly to its corresponding wood, then use wood screws to fix the back cover on the wall.

Note:

Install the back cover of wire controller on the even wall as possible as can. When tightening the wood screw, do not use to tight force, otherwise the wire controller may be damaged.

Switch

Mark

ON

OFF

1

3 grades fan speed

2 grades fan speed

2

Have rise and drop

No rise and drop

3

Swing

Not Swing

4

The collection temperature

The collection temperature

of main panel

of panel

 

Under this series, the switch is set as:1.ON 2. OFF 3. OFF 4.OFF

3.Indoor unit wire connection

Connect the terminals (A, B, C, D,) on the wire controller to the terminals on the indoor PC panel (A, B, C, D,) respectively.

Arrange wire

AB CD from this part

Back cover wire controller

Note:When connecting wire, please keep a certain distance between signal wire and electric wire. (over 10mm)

 

 

 

 

 

 

 

 

 

Dimension of signal wire:

 

 

 

 

 

 

 

 

 

 

Type of wire Shield wire (4 cords)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Dimension

 

0.33mm2

 

 

 

 

 

 

 

 

 

Upper cover of

*The connection between indoor unit

 

 

 

 

 

 

 

 

 

and wire controller and indoor unit

 

 

 

 

 

 

 

 

wire controller

 

 

 

 

 

 

 

 

 

 

 

and outdoor unit should use shield

Note:

 

wire. And the two ends of the shield

 

wire should be grounded, otherwise,

Confirm the connection part of terminals

 

 

the disturbance will cause unit abn-

is firm and will not touch shield wire.

 

 

ormal operation.

 

 

 

 

 

 

4. Cover the wire controller upper cover

 

 

 

 

 

 

 

Pay attention not to press the connection wire.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Shield wire

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Note: (1) The power switch and the signal

 

Grounded

 

Grounded

 

 

 

 

wire are self-provided.

 

 

 

 

 

 

 

 

 

 

 

 

 

26

 

 

(2) Do not touch PC board by hand.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Page 27 Page 29
Image 28
Page 27 Page 29
Contents Usersí Attention************11 Maintenance Safety Precautions**********4-5 Operation InstructionBefore Use Operation Points Characteristics of Products Characteristics of ProductsFar distance monitoring Operation points Name of Parts Wire Controller Electric heating display ClockSafety Precautions Installation Safety PrecautionsOFF Fan operation Operation instructionPress the ON/OFF button to turn off the unit Set temperature Auto/Cooling/Dehumidifying/Heating operationAbout Auto operation HintsTimer On/Off function After turning on the unit, set the desired working modeTimer On-Off function Sleep operation Usersí Attention Do not put articles around the air inlet and outletMaintenance Clean the air filterClean Use cleaner or water to clean to remove dustCleaning the air filter or air inlet and casing After cleaning the air filter, it must be reinstalledTurn on the power Check the following itemsTroubleshooting When Troubles Occur Please cut off power immediately and contact with supplerThen contact the commissioned repair After taking the following measureCenter Installation instruction Accessories attached with the unit Installation procedure Install indoor unitChoose installation place Space installation needed unit mmInstall the hoisting screw Adjust to level Installation of indoor unitChoose the air sending of the fan motor Drain hose Good pipe system Improper pipe systemProcedure Test of drainage systemInstallation of air suction and discharging duct Length difference amongEvery duct is limited below AAbsorb of fresh air single air supplying bAir dischargingExamples of improper installation Special air discharging outletRemove the upper cover of wire controller Install wire controllerIndoor unit wire connection Cover the wire controller upper coverConnection of pipe Electric wiring Wiring method Wiring method of orbicular terminalWiring method of straight terminal Pressing method of connection wire

AD422BMBAA specifications

The Haier AD422BMBAA is a remarkable appliance that embodies innovation and practicality, designed to meet the demands of modern households. This refrigerator stands out with its sleek and contemporary design, making it a stylish addition to any kitchen. With a focus on energy efficiency, this model operates with minimal power consumption, allowing homeowners to save on electricity bills while reducing their carbon footprint.

One of the standout features of the Haier AD422BMBAA is its spacious interior, which is thoughtfully organized to maximize storage capacity. It includes adjustable shelves that can be rearranged to accommodate larger items like party platters or tall beverage containers. The generous capacity ensures that food items are easily accessible, making meal preparations a breeze.

The refrigerator adopts advanced cooling technology, ensuring that food stays fresher for longer. It employs a multi-air flow system that distributes cool air evenly throughout the fridge, preventing hot spots and ensuring that every corner is adequately chilled. This feature is essential for preserving the quality and nutritional value of perishable items.

Additionally, the Haier AD422BMBAA incorporates a frost-free freezer, which eliminates the need for manual defrosting. This convenient feature prevents ice build-up, ensures optimal storage space, and facilitates easy access to frozen foods. The freezer section is designed with specialized compartments that help organize various types of frozen goods, making it easy to find what you need without rummaging through clutter.

Another notable characteristic of this refrigerator is its innovative temperature control system. Users can easily adjust settings using a user-friendly digital display, ensuring that the internal conditions are ideal for all types of food. This precision allows homeowners to customize their refrigeration experience based on their specific needs.

Moreover, the Haier AD422BMBAA is built with energy-efficient components that comply with modern environmental standards. This appliance is designed not only for functionality but also with a commitment to sustainability in mind.

In conclusion, the Haier AD422BMBAA is more than just a refrigerator; it is a perfect blend of design, technology, and environmental consciousness. Its ample storage space, advanced cooling capabilities, and user-friendly features make it an optimal choice for families looking to enhance their kitchen experience.
Top Page Image Contents