Tannoy DI5 warranty Architectural specifications Di5

Di5

Architectural specifications Di5

The weather resistant, full bandwidth surface mount speaker system shall consist of a 110mm (4.50") full range, point source ICT™ transducer mounted in an optimally tuned vented, injection moulded high impact polystyrene (HIPS) enclosure, rated IP64 to EN60529 (IEC529). The protective grille shall be constructed from steel with a weather resistant coating.

Performance of the Di5 surface mount speaker shall meet or exceed the following criteria: The system shall have a conical coverage pattern of 90 degrees (-6dB). Frequency response measured on axis shall be 80Hz - 30kHz (-10dB from rated sensitivity, average over stated bandwidth. Measured at 1 metre in an anechoic chamber) with no equalisation. Sensitivity shall be 88dB (1W = 2.45V for 6 Ohms). Long term power handling capacity as defined in EIA-426B test shall be 50W, recommended amplifier power 100W. The nominal system impedance shall be 6 Ohms (in low impedance setting).

A termination recess shall be integrated with the rear panel, a removable Euroblock type locking connector with screw terminals for secure wire termination with "loop through" facility shall be provided. A yoke mounting bracket shall be included with the speaker system and additional security shall be provided by a tie back point.

The dimensions shall not exceed 240.7 x 155 x 162mm (9.47 x 6.10 x 6.38”). The surface mount speaker system shall be the.....Di5.

Architectural specifications Di5t

The weather resistant, full bandwidth surface mount speaker system shall consist of a 110mm (4.50") full range, point source ICT™ transducer mounted in an optimally tuned vented, injection moulded high impact polystyrene (HIPS) enclosure, rated IP64 to EN60529 (IEC529). The protective grille shall be constructed from steel with a weather resistant coating.

Performance of the Di5t surface mount speaker shall meet or exceed the following criteria: The system shall have a conical coverage pattern of 90 degrees (-6dB). Frequency response measured on axis shall be 80Hz - 30kHz (-10dB from rated sensitivity, average over stated bandwidth. Measured at 1 metre in an anechoic chamber) with no equalisation. Sensitivity shall be 88dB (1W = 2.45V for 6 Ohms). Long term power handling capacity as defined in EIA-426B test shall be 50W, recommended amplifier power 100W. The nominal system impedance shall be 6 Ohms (in low impedance setting).

The Di5t speaker system shall be equipped with a 30W high performance line transformer for use in 70.7 or 100 Volt distributed audio systems with

30 / 15 / 7.5 / 3.75* Watt, OFF and Low Impedance taps available. An easily accessible rotary switch located under the rubber trim on the top of the cabinet shall be available for selecting transformer and low impedance settings.

A termination recess shall be integrated with the rear panel, a removable Euroblock type locking connector with screw terminals for secure wire termination with "loop through" facility shall be provided. A yoke mounting bracket shall be included with the speaker system and additional security shall be provided by a tie back point.

The dimensions shall not exceed 240.7 x 155 x 162mm (9.47 x 6.10 x 6.38”). The surface mount speaker system shall be the.....Di5t.

*70 Volt only

Tannoy United Kingdom

Tannoy North America

Tannoy Deutschland

Tannoy France

T:00 44 (0) 1236 420199

T:00 1 (519) 745 1158

T:00 49 (180) 1111 881

T:00 33 (0)1 7036 7473

E:enquiries@tannoy.com

E:inquiries@tannoyna.com

E:anfragen@tannoy.com

E:ventes@tannoy.com

Tannoy adopts a policy of continuous improvement and product specification is subject to change Di5 data file // issue 1.06 // 14.01.08