PHL Audio specifications 1500 1510, 68.5 max

1500 ■ 1510

6.5” Midrange Drivers

		1500		1510
TYPICAL CHARACTERISTICS
Rated impedance	Z	8		16	Ω
Reference efficiency (1 W@1 m)	-	98		98	dB SPL
Usable frequency range 1	-	400–5000		400–5000	Hz
Power handling capacity 2 (AES)	-	250		250	W
Max Sound Pressure Level 3	SPLmax	119		119	dB SPL
Min. impedance modulus	Zmin	6.2 @ 650Hz 12 @ 600Hz			Ω
Voice-coil inductance 4 @ 1 kHz	Le1k	0.58		1.14	mH
@ 10 kHz	Le10k	0.30		0.60	mH
Bl product	Bl	11.0		15.8	N/A
Moving mass	Mms	0.0105		0.0105	Kg
THIELE-SMALL PARAMETERS : TYPICAL (QC LIMITS)
Resonance frequency 5	Fs	130 (±25)		130 (±25)	Hz
DC resistance 6	Re	5.5 (±0.6)		10.6 (±1.1)	Ω
Mechanical quality factor	Qms	4.1		4.1	1
Electrical quality factor	Qes	0.39		0.37	1
Total quality factor	Qts	0.36		0.34	1
Mechanical suspension compliance	Cms	145		145	10-6m/N
Effective piston area	S	0.0150		0.0150	m2
	d
Equivalent Cas air load	Vas	0.0045		0.0045	m3
Max. linear excursion	Xmax	±1.0		±1.0	mm
Linear displacement volume	Vd	0.0150		0.0150	10-3 m3
Half-space efficiency		2.4		2.6	%
Unity load volume	Vas Qts2	0.6		0.5	10-3 m3
ABSOLUTE MAXIMUM RATINGS
Short term max. input voltage 7	Vmax	90		125	V
Max. excursion before damage	Xdam	±2.5		±2.5	mm
Ambient operating temperature		–10	to	+50	°C
Storage temperature 8		–20	to	+70	°C
Environmental conditions 9		Outdoor✚
APPLICATION INFORMATION
Air volume occupied by the driver 10		0.64		0.64	10-3 m3
Speaker net mass		2.60		2.60	Kg
Recommended reflex box	Vb/Fb	3L / sealed			L / Hz
Electrical polarity	A positive voltage applied on the red
	terminal produces forward cone motion.

max.187.5	angles)(on	PHYSICAL CHARACTERISTICS
		4 x Ø 5.3 Holes on Ø 172
Ø
+ Red dot
NO
FAST
8.0 x35 .6	inalerm T

Ø 162.5 max.

8

68.5 max.

Ø 139 max.

Ø 145.3 max.

SPECIFICATION NOTES

Note 1 : Allowing for energy response, excursion capability, Power spectrum, and -3dB low freq. roll-off for standard reflex tuning.

Note 2 : Established at 20°C ambient temp, according to AES2-1984 standard using IEC268-1 simulated programme signal and a 3 liter sealed test enclosure with a 2nd order high-pass filter @ 800Hz.

Note 3 : Established at 1m on axis of the loudspeaker mounted

in test enclosure, when driven at full AES Power Handling Capacity, including 3dB of thermal compression loss.

Note 4 : Measured at 20 mA in free air.

Note 5 : Measured at 20 mA and 20°C ambient temp. in free air conditions, after full run and rest.

Note 6 : Measured at 20°C ambient temp.

QC limits are ±10 %

Note 7 : Stated in RMS voltage according to IEC 268-5.

Note 8 : Includes shipping conditions. The lower limit prevents from demagnetization.

Note 9: Our products are classified in three categories : Indoor, Outdoor, and Outdoor✚ for permanent outdoor use or severe conditions.

Note 10 : Calculated for front mounting on to a 18 mm thick board.

461, rue des chênes ■ Z.A 77590 CHARTRETTES FRANCE

Tél : 33 01 64 81 29 80

Fax : 33 01 60 69 10 28

e-mail : phlaudio@phlaudio.com

http: //www.phlaudio.com

PHL Audio S.A. provides these specifications as representative of current production after conditioning. Because of our continuous research, they are subject to change without notice.