Figure 10
Unpacking the Loudspeaker
To protect the fine finish of the XCS1K Loudspeaker Sys- tem during the assembly process, it is advisable to prepare a suitable area. A freshly vacuumed carpeted area covered with a soft, clean fabric, such as a large bed linen or blan- ket would be suitable. Start by unpacking the Loudspeaker. It is recommended that the Professionals at your McIn-
tosh Dealer, who are skilled in all aspects of installation and operation, install the XCS1K Loudspeaker System and any associated audio equipment.
CAUTION: The XCS1K Loudspeaker weighs 133 pounds (60.3 kgs). It requires two or more persons to safely handle during assembly, adjustment and placement in the room.
1. Orient the XCS1K shipping carton with the arrows on the outside of the carton pointing upward.
2. Remove the banding material from the shipping carton.
8
Figure 9
Height
Adjustment Screws
Figure 12
Locking
Screws
Cradle
(Top View)
Figure 11
Location in the Room
The XCS1K Loudspeaker is designed for use as a Center Channel in a Home Theater System. The optimal method for selecting all the Loudspeaker Locations in a Home Theater System includes the use of a real time spectrum analyzer operated by an experienced system installer. An uncompromising installation would take into consideration the floor, wall and ceiling coverings, the type and place- ment of furniture and can even include the architectural design of the room and its construction materials. In those instances where placement in the room is fixed, an en- vironmental equalizer may be needed to restore proper musical balance.
The XCS1K Loudspeaker’s Smooth Frequency Re- sponse may be altered by
a large object(s) located in the path of the sound waves or by locating the Loudspeaker too close to a side wall. There should
be an unobstructed area in front of the XCS1K Loudspeaker on either
side of the center axis for
the best performance. The optimum location in a Home Theater System is
directly under or in front
of the TV/Monitor. Refer to figures 9 and 10.
Installation
Installation
3.Lift off the top of the shipping carton and set it aside.
4.Remove the smaller inner carton labeled XCS1K Cradle.
5.Open the inner carton, remove the Cradle and place it in the final location of the XCS1K Loudspeaker. Refer
to figure 11.
6. Remove the Top Foam from the Loudspeaker.
7. Remove the Loudspeaker
from the Bottom Foam.
8. Remove the Blue Protective Cloth Cover from the Loud- speaker. Set the Loudspeaker and Cover aside on the previ- ously prepared area.
Adjusting the Elevation of the Loudspeaker
The acoustic output of the XCS1K Loudspeaker may be directed to line up with the height of the average ear in the prime viewing/listening area. There is a 30 degree range of adjustment built-in.
1. Using an approprate tool, loosen the hex head screws
on the insides of the XCS1K Cradle. Refer to figure 12.
2. Before placing the XCS1K Loudspeaker on the Cradle, rotate the top/sides of the
Cradle to the desired angle so
the sound will be directed toward ear level when seated in the main view- 
ing/listening area.
| 4. Tighten the height | |
| adjustment and | |
| locking screws on | Top View of |
| the insides of the |
| Lift Areas |
| Cradle. | Figure 13 |
| 5. Refering to the lift |
| |
| areas in figure 13, lift up on | |
| the sides and center rear of | |
| the Loudspeaker with two or | |
| more persons. Place the Loud- | |
| speaker on the Cradle. Refer | |
| to figure 14. | |
Note: When lifting up on the sides of the Loudspeaker, be carefull as to not remove the detachable sides.
6. Proceed to “How to connect” starting on page 9.
