EAW LA325 specifications Dimensional Drawing, Specifications

SPECIFICATIONS LA325

DIMENSIONAL DRAWING

	A
			NOTES:
			1. SYMBOL INDICATES 4.00 X 1.35 FLY TRACK.
			2. SYMBOL INDICATES MOUNTING
8.90			POINT, 3/8-16 THREADED HOLE.
			3. SYMBOL INDICATES RUBBER FOOT.
			4. SYMBOL INDICATES CENTER OF BALANCE.
	C		5. WEIGHT APPROX 165 LBS.
	L		6. SHIPPING WEIGHT APPROX. 173 LBS.
	14.22
	20°			2X HANDLE
	TOP A	2.13	16.34			7.00
	20.84		8.86			C
						L
				2.97
		38°		17.82		23.06
					21.37
		3.00	LA
47.00				4.50	4.25
47.50
		43.00		3X HANDLE
				INPUT
	FRONT		VIEW A-A			BACK
GRILLE PARTIALLY SHOWN		DIMMENSIONS APPLY
	14.24		TO BOTH SIDES
		3X 4.50
8.44
	C
	L
		3.03
8.86
		19.50
		3X 8.75
8.80	14.34				510024 (4)
	BOTTOM
Manufacturing tolerances are +/- 0.13 and +/- 1°

A & E SPECIFICATIONS

The three-way full range loudspeaker systems shall incorpo- rate 2x 15-in LF transducers, 2x 7-in cone MF transducers and a 2-in exit/3-in voice coil compression driver HF transducer.

The LF drivers shall be mounted in a vented enclosure tuned for optimum low frequency response. The MF drivers shall be mounted in a sealed subenclosure. The HF driver shall be loaded on an asymmetrical wave guide plate with a nominal coverage pattern of 90° (h) x 70° (v). An internal passive fil- ter network shall provide fourth order acoustical crossover and system equalization.

System frequency response shall vary no more than ±3 dB from 50 Hz to 20 kHz measured on axis. In passive mode, the loudspeaker shall produce a Sound Pressure Level (SPL) of 100 dB SPL on axis at 1 meter with a power input of 1 Watt, and shall be capable of producing a peak output of 133.8 SPL on axis at 1 meter. It shall handle 600 Watts of amplifier power (AES Standard) and shall have a nominal impedance of 4 Ohms.

In bi-amped mode, the mid/high frequency section shall meet all passive mode performance criteria. In addition, the low frequency section in bi-amped mode shall be capable of pro- ducing a peak output of 136.0 SPL on axis at 1 meter. The low frequency section in bi-amped mode shall handle 1000 Watts of amplifier power (AES Standard) and shall have a nominal impedance of 4 Ohms.

The loudspeaker enclosure shall be trapezoidal in shape. It shall be constructed of exterior grade Baltic birch plywood and shall employ extensive internal bracing. It shall be fin- ished in wear resistant textured black paint. Input connectors shall be dual Neutrik NL4 Speakon. The system shall include a switch allowing it to be operated in biamp or passive power- ing mode. The following mounting/suspension hardware shall be provided: two 3-position flytrack with integral 3/8"-16 threaded mounting points (2 on top) and eight 3/8"-16 threaded mounting points (2 per side, 3 bottom, 1 back). The front of the loudspeaker shall be covered with a powder coat- ed perforated steel grille.

The three-way full range loudspeaker shall be the EAW model LA325.

One Main Street, Whitinsville, MA 01588	508 234 6158	Toll Free 800 992 5013	FAX 508 234 8251	info@eaw. com	www. eaw. com
EAW products are continually improved. All specifications are therefore subject to change without notice.			LA325/0004838/001/2 pp	September 2002	Printed in USA