Sony FDL-PT222 AFT Fine ADJUSTMENTT201, RF. AGC Adjustment RV201, Contrast Adjustment RV402

FDL-PT222

[AFT FINE ADJUSTMENT(T201)]

1. Connect a 1 kilohm resistor between JL77 (+4.5V) and JL28 (RF AGC).

Note : Perform this adjustment as the last step in the process since drift may occur due to aging.

2. Switch the sweep signal to CW.

fo= 45.75 MHz± 5 kHz, -30±5dBm

Apply the above signal between JL26 (IF) and JL27 (IF GND) and then make a fine adjustment of T201 so that the level be- tween JL31 (AFT) and JL30 (D.GND) reaches2.2V± 0.4VDC.

3.Remove the 1 kilohm resistor connected between JL77 (+4.5V) and JL28 (RF AGC).

3-3.B BOARD ADJUSTMENT

- B board - (Component side)

RV301

RV402

[RF. AGC ADJUSTMENT (RV201)]

1.Set S601 to VHF position and receive a VHF color bar signal issued from a signal generator.

2.Adjust RV201 and align the screen for the optimal point so that the snow noise disappears.

[CHANNEL DISPLAY POSITION ADJUSTMENT

(RV001, RV002, RV004)]

1.	Set S601 to VHF position, a potentiometer (47kΩ± 15kΩ )
	across JL25(CS) and JL77 (+4.5 V) as shown in Fig. 2-6 and
	short the points JL21(CH CAL) and JL30 (D.GND).
2. Receive channel 2 and align the channel display positions with
	RV002(VP).
3. Receive channel 13 and align the display bar with RV004(VA).
4. Align while performing tracking to mutual interference in the
	above steps 2 and 3.
5.	Receive channels 3 & 4 and confirm that the display bar is

[CONTRAST ADJUSTMENT (RV402)]

1.Receive the stepped waveform signal in 10 steps.

2.Observe the waveform across JL83(G) and JL67(GND).

3.Check the contrast changes by turning RV402.

4.Connect an oscilloscope between JL84 (AUTO CB) and JL67 (D. GND) and adjust RV402 so that the voltage of A portion becomes 2.2+-0.2V.

5.Check the waveform as shown in Fig. 3-5.

6.At the same time, check the points C and D are within the period as shown in Fig. 3-5.

100 IRE

within the standards.

6. Set S601 to UHF.

JL83

Contrast changes

7. Receive channel 14 and align the display position with

RV001(UP).

8. Receive channel 69 and confirm that the display bar is within

the standards.

Once again receive channel 14 and confirm that the display bar is within the standards.

Note : Use caution since shifting channel 69 will also cause channel 14 to shift.

9.Remove the potentiometer (47kΩ +15kΩ ) you connected be- tween JL25(CS) and JL77(+4.5V). Also remove the short you connected between points JL21 (CH CAL)and JL30(D.GND).

JL25 (CS)	Display bar
	JL77(+4.5V)
15kΩ	Channel No.
	6
	VR(47kΩ )
	*Channel No. and display
	bar are to be in line.
	Fig. 3-4
	Fig. 3-3

0 IRE

D

C

JL84

A=2.2± 0.2VDC

Fig. 3-5

[COLOR PHASE (TINT) ADJUSTMENT (RV301)]

1.Receive the color bar signal from the signal generator.

2.Observe the waveform across JL81(B) and JL67(D.GND).

3.Adjust RV301 (TINT) so that the waveform level becomes as shown in Fig. 3-6.

Fig. 3-6

– 8 –