La Crosse Technology WS-9730U-IT instruction manual Table of Contents

Page 1
Hanging hole
Battery compartment
cover
Foldout
Stand

WS-9730U-IT Instruction Manual

Table of Contents

 

Topic

 

 

Page

 

Inventory of Contents

 

 

1

 

 

Features

 

 

1

 

 

Setting Up

 

 

1

 

 

Battery Installation

 

 

1-2

 

 

Function keys

 

 

2

 

 

LCD Screen and Settings

 

 

2

 

 

Manual Settings

 

 

2-3

 

 

Weather Forecast and Tendency

 

2

 

 

Display of Indoor Temperature and Humidity Reading

 

3

 

 

Display of Outdoor Temperature Reading

 

4

 

 

Display of Indoor Maximum and Minimum records

 

4

 

 

Display of Outdoor Maximum and Minimum records

 

4

 

 

915 MHz Reception

 

 

4

 

 

Mounting

 

 

4

 

 

Care and Maintenance

 

 

5

 

 

Specifications

 

 

5

 

 

Warranty Information

 

 

5

 

 

 

 

 

 

 

This product offers:

INSTANT TRANSMISSION is the state-of-the-art new

 

 

 

 

wireless transmission technology, exclusively designed and

 

 

developed by LA CROSSE TECHNOLOGY. INSTANT

 

 

TRANSMISSION offers you an immediate update (every 4 seconds!) of all your outdoor data measured from the sensors: follow your climatic variations in real-time!

INVENTORY OF CONTENTS

1.Wireless Weather Station

2.Wireless Outdoor Temperature Sensor (TX29U-IT) and mounting bracket.

3.Instruction Manual and Warranty Card.

FEATURES:

The Weather station

LCD

Display

Function

ManualKeystime setting

12/24 hour display

Hour and minute display

Wireless transmission at 915 MHz

Signal reception intervals at 4-second

Display indoor and outdoor temperature and indoor humidity (% RH)

Temperature displayed in degrees Fahrenheit (°F) or Celsius (°C) selectable

Weather forecasting with 15 easy-to-read weather forecast signs featured by Weather girl

Indoor comfort level indicator

Indoor and Outdoor temperature display with MIN/MAX recording

All MIN/MAX recordings can be reset

Low battery indicator

Table standing/ Wall mounting

The Outdoor Temperature Sensor

Remote transmission of outdoor temperature to Weather Station by 915 MHz

Shower proof casing

Wall mounting case (Mounting at a sheltered place. Avoid direct rain and sunshine)

SETTING UP:

Note:

This weather station receives only one outdoor sensor.

1.First, insert the batteries into the Temperature sensor. (see “Install and replace batteries in the Temperature sensor“).

2.Immediately after and within 30 seconds, insert the batteries into Weather station (see “Install and replace batteries in the Weather station”). Once the batteries are in place, all segments of the LCD will light up briefly. Following the time as 12:00 and the "Weather girl" icon will be displayed. If these are not displayed after 60 seconds, remove the batteries and wait for at least 10 seconds before reinserting them.

3.After inserting the batteries, the Weather station will start receiving data from the sensor. The outdoor temperature and the signal reception icon should then be displayed on the Weather station. If this does not happen after 3 minutes, the batteries will need to be removed from both units and reset from step 1.

4.In order to ensure sufficient 915 MHz transmission however, this should under good conditions be a distance no more than 100 meters between the final position of the Weather Station and the sensor (see notes on “Mounting” and “915 MHz Reception”).

Note:

If the signal reception is not successful on the first frequency (915MHz) for 45 seconds, the frequency is changed to 920MHz and the learning is tried another 45 seconds. If still not successful the reception is tried for 45 seconds on 910MHz. This will also be done for re- synchronization.

BATTERY INSTALLATION

INSTALL AND REPLACE BATTERIES IN THE WEATHER STATION

The Weather station uses 2 x AA, IEC LR6, 1.5V batteries. To install and replace the batteries, please follow the steps below:

1. Remove the cover at the back of the Weather station.

2. Insert batteries observing the correct polarity (see marking).

3. Replace compartment cover.

INSTALL AND REPLACE BATTERIES IN THE TEMPERATURE SENSOR

The Temperature Sensor uses 2 x AA, IEC LR6, 1.5V battery. To install and replace the batteries, please follow the steps below:

1. Remove the battery compartment cover at the back of the sensor.

2. Insert the batteries, observing the correct polarity (see marking).

3. Replace the battery compartment cover on the unit.

Note:

In the event of changing batteries in any of the units, all units need to be reset by following the setting up procedures. This is because a random security code is assigned by the sensor at start-up and this code must be received and stored by the Weather station in the first 3 minutes of power being supplied to it.

Image 1
Contents Table of Contents Manual Settings Battery ChangeManual Time Setting Calendar SettingWeather Tendency Indicator Temperature Unit SettingComfort Level Indicator Display of Indoor Temperature and Humidity ReadingDisplay of Outdoor Maximum and Minimum Temperature Records Display of Outdoor Temperature ReadingDisplay of Indoor Maximum and Minimum Temperature Records Resetting the Indoor MAXIMUM/ Minimum RecordsSpecifications Care and Maintenance