JBL SMS1 owner manual Wall Mounting

Page 13

Wall Mounting

Both the Subwoofer and the Satellites arrive ready for wall mounting. The Subwoofer cabinet must first be separated from the wall baffle. To do this, simply remove the screws from all the mounting tabs. Then pull the cabinet off of the baffle. Be sure to disconnect the cables attaching the subwoofer driver to the electron- ics as soon as the cable is accessible. In the case of the Satellites, the InvisiBall base and arm are designed so that optimum aiming angles can be achieved with the base firmly mounted to a wall or to a ceiling. In the case of the Subwoofer, the Baffle is designed to mount to a wall surface only. IMPORTANT NOTE: For proper convection cooling of the built-in power amplifiers, the SMS1-SUB Subwoofer MUST be installed upright. Do NOT install SMS1-SUB on a ceiling.Detailed descriptions of procedure for mounting are covered in the INSTALLATION AND HOOKUP sections of this manual. There are also options for mounting the SMS1-SAT’s to ceilings either for aesthetic or architectural reasons. But the basics of place- ment still apply. The Satellites should be near the corners of the room, aimed to the center of the room approximately 4-ft (1.2m) above the floor. The Subwoofer(s) should be placed near corner junctions when possible and if used in multiples, should be placed asymmetrically within the room.

Floor Placement

The Subwoofer can also be placed directly on the floor, or on a shelf (capable of supporting it) using the INCLUDED Subwoofer Feet. Again, refer to the INSTALLATION AND HOOKUP Section of the manual for information on placing the Subwoofer on the floor.

Running Wires

Once the location for each of the speakers is understood, running wires for all connections is thenext step. One of the best options is the use of hard conduit, flex conduit, or bare wiring through walls and ceilings. It is the safest and least visually distracting method. Another option is to run hard conduit externally on walls and ceilings (and paint over it, if necessary), as the wiring is still well protected and it is a visually clean look. If neither of these options is available, then be sure to fix any wires in place. Hanging loose wire is unsafe, for the equipment and people, and visually unappealing. It could easily take away from the aesthetics of the architecture.

For a typical SMS1 System, the necessary wire runs are as follows:

-Four runs of speaker wire, one run to each SMS1-SAT, from the SMS1-SUB

-One run of Mono or Stereo Audio Signal, from the source (Soundzone Controller, CD Player, DVD Player, Subscription Music Service, etc.) to the subwoofer.

-One Paging Microphone input connection (optional) to subwoofer

-One Cat-5 Cable for Remote Wallplate (optional) to subwoofer

-Power to the SMS1-SUB

The Subwoofer requires power. This can be done in several ways. If you are fortunate enough that you can mount the Subwoofer directly over a junction box or outlet, this is a very good option. There are knockouts and access plates on the Subwoofer’s Baffle that will allow the power cord to just plug into the outlet. If this is not an option, an electrician can run power from some point, through the wall, to the desired Subwoofer location and install a junction box or outlet that can then be accessed. It is also important to run power through one junction box and audio through another. Be sure that, regardless of how power is brought to the location of the Subwoofer, it terminates in a standard, grounded power socket. Detail about exact hookup and installation of system components is covered below. Remember to always be aware of and adhere to local, regional and national requirements for components of this nature.

10

Image 13
Contents SMS1 Page Table of Contents Quick Start Guide Introduction SMS1-System Components and PartsWall Baffle and Electronic Module SMS1-SUBControl Panel Control Panel and Connector PanelConnector Panel Placement InstallationCoverage Subwoofer Wall Mounting Wall Baffle Mounting Holes Installation and Hookup of the SubwooferPage Connecting the Subwoofer Driver Marking the Wall with the InvisiBall Base Installation and Hookup of the SatellitesWire Management Clips Tuning Attaching the Security Panel Additional Applications Power Capability SpecificationsWarranty & Contacting JBL SMS1 SYS MAN-PL

SMS1 specifications

The JBL SMS1 is a state-of-the-art sound system processor designed specifically for professional sound applications. It excels in offering unparalleled sound quality and advanced processing capabilities, making it a go-to choice for audio engineers and sound professionals alike. With its compact design, the SMS1 is highly versatile, suitable for both live sound scenarios and fixed installations.

One of the standout features of the JBL SMS1 is its ability to perform precise room tuning. This is essential for optimizing sound in various environments, whether it be a concert hall, auditorium, or nightclub. The SMS1 utilizes advanced digital signal processing (DSP) technology, allowing users to tailor the sound to fit the acoustics of any space. This functionality ensures that the audio experience remains consistent and high-quality, regardless of the listening environment.

The SMS1 is equipped with multiple inputs and outputs, allowing for flexible connections to various audio sources and speakers. This includes balanced XLR connectors for professional-grade signal transmission, providing low-noise and high-quality audio signals. Additionally, the unit supports a broad range of sample rates, enabling compatibility with a variety of audio formats and devices.

Integration with other equipment is seamless, thanks to the SMS1’s MIDI capability and networked control options. Users can easily control multiple SMS1 units and other compatible devices through a centralized interface, streamlining the overall sound management process. This is particularly beneficial in live settings where performance dynamics can change quickly.

Another noteworthy characteristic of the JBL SMS1 is its user-friendly interface. The device features an intuitive LED display, making navigation through settings and adjustments straightforward for operators, even under pressure during live events. The advanced processing algorithms ensure that the audio output is not only powerful but also crystal clear, enhancing the overall listening experience.

Finally, the durability of the JBL SMS1 is built to withstand the rigors of professional use. Its robust construction ensures reliable performance, whether in a touring setup or a permanent installation. With the combination of cutting-edge technology, user-centric design, and exceptional sound quality, the JBL SMS1 is an indispensable tool for audio professionals looking to elevate their sound systems to new heights.