AZ1080/01 03/07/02 11:31 Page 7
Power Supply
Batteries contain chemical substances, so they should be disposed of properly.
Incorrect use of batteries can cause electrolyte leakage and will corrode the compartment or cause the batteries to burst.Therefore:
•Do not mix battery types: e.g. alkaline with carbon zinc. Only use batteries of the same type for the set.
•When inserting new batteries, do not try to mix old batteries with the new ones.
•Remove the batteries if the set is not to be used for a long time.
Using AC Mains
1Check if the mains voltage, as shown on the type plate located on the bottom of the set, corresponds to your local power supply. If it does not, consult your dealer or service centre.
~ |
4To switch off completely, unplug the mains lead from the wall socket.
•Unplug the mains lead from the wall socket to protect your set during heavy thunderstorms.
The type plate is located on the bottom of the set.
Switching power on/off:
Save energy
Whether you are using mains or battery supply, to avoid unnecessary energy consumption always adjust the source selector to TAPE/OFF and check if the cassette keys are released.
| 1080 |
|
|
|
|
|
|
|
| |
Z |
|
|
|
|
|
|
|
| ||
A |
|
|
|
|
|
|
|
|
|
|
|
|
| B |
|
|
|
|
|
| |
|
| ITABLECOMPATI | LE |
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
| ||
| R |
|
|
|
|
|
|
|
| |
W |
|
|
|
|
|
|
|
|
| |
E |
|
|
|
|
|
|
|
|
|
|
DR |
|
|
|
|
|
|
|
|
|
|
C |
|
|
|
|
|
|
|
|
|
|
LI |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| V |
|
|
|
|
|
|
|
|
|
| OLU |
|
|
|
|
|
|
|
|
|
| ME |
|
|
|
| CK |
|
| REPEAT |
|
| |
E |
|
|
| CD TRA |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
S |
|
|
|
|
|
|
|
|
|
|
U |
|
|
|
|
|
|
|
|
|
|
A |
|
| ST |
|
|
|
|
|
|
|
P |
|
|
|
|
|
|
|
|
| |
/ |
|
| O |
|
|
|
|
|
| |
Y |
|
|
| P |
|
|
|
| HUF | FLE |
A |
|
|
|
|
|
|
|
| ||
L |
|
|
|
|
|
|
| S | ||
P |
|
|
|
|
|
|
| AT |
| |
|
|
|
|
|
|
|
|
| PE |
|
|
|
|
| EARC | H |
|
| B | R E |
|
|
|
|
| S |
|
| OOS |
| ||
|
|
|
|
|
|
|
| IC BASS |
| |
|
|
|
|
|
|
|
| AM | T |
|
|
|
|
|
|
| D | Y | N |
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
| DBB |
| |
General operation
1To select your sound source adjust the source selector to CD, AM (MW), FM or TAPE/OFF.
English
2Connect the mains lead to the AC MAINS inlet and the wall socket.The power supply is now connected and ready for use.
3If your set is equipped with a voltage selector, located inside the battery compartment, adjust the selector to match the local mains. Disconnect the mains lead if this selector has to be reset.
2Adjust the sound with the VOLUME and DBB (Dynamic Bass Boost) controls.
3To switch off the set, adjust the source selector to TAPE/OFF position and check the cassette keys are released.
7