16.DC CONNECTION PRECAUTIONS
a.Connect and disconnect the DC output clamps only after setting the charger switches to the OFF position and removing the AC cord from the electric outlet. Never allow the clamps to touch each other.
b.Attach the DC clamps to the battery post and twist or rock back and forth several times to make a good connection. This tends to keep the clamps from slipping off the terminals and helps to reduce the risk of sparking.
17.STOP/GO LITE INSTRUCTIONS
When used properly, the STOP/GO LITE will indicate whether clamp connections will be correct. Connect the positive (red) clamp to the positive (POS, P, +) battery post. Touch the contact button of the negative (black) clamp to the other battery post. Observe the L.E.D. lights in the STOP/GO LITE: GREEN LIGHT: The first connection is correct. Make the second clamp connection per instructions.
RED LIGHT: The first connection made with the positive clamp to the battery is incorrect. Attach the positive clamp to the other battery post and retest.
RED AND GREEN LIGHT: The battery charger is turned on. Turn the charger "OFF" and retest.
NO LIGHT: Check for a shorted or open battery. Clean any corrosion from the clamp jaws and the battery post and retest. If still no light, use a voltmeter or other means to make certain you have properly identified the polarity of the battery post. Then attach the clamps per instructions, disregarding the
STOP/GO LITE.
18.FOLLOW THESE STEPS WHEN THE BATTERY IS INSTALLED IN A VEHICLE. A SPARK NEAR THE BATTERY MAY CAUSE BATTERY EXPLOSION. TO REDUCE THE RISK OF A SPARK NEAR THE BATTERY:
a.Read the section "STOP/GO LITE INSTRUCTIONS" before proceeding.
b.Position the AC and DC cords to reduce the risk of damage by the hood, door, or moving engine parts.
c.Stay clear of fan blades, belts, pulleys, and other parts that can cause injury to persons.
d.Check the polarity of the battery post. The POSITIVE (POS, P, +) battery post usually has a larger diameter than the NEGATIVE (NEG, N,
e.Determine which post of the battery is grounded (connected) to the chassis. If the negative post is grounded to the chassis (as in most vehicles), see item "f". If the positive post is grounded to the chassis, see item "g".
f.For
g.For
h.When disconnecting the charger, turn the switches to OFF, disconnect the AC cord, remove the clamp from the vehicle chassis, and then remove the clamp from the battery terminal.
i.See the operating instructions for length of charge information.
19.FOLLOW THESE STEPS WHEN THE BATTERY IS OUTSIDE THE VEHICLE. A SPARK NEAR THE BATTERY MAY CAUSE BATTERY EXPLOSION. TO REDUCE THE RISK OF A SPARK NEAR THE BATTERY:
a.Read section "STOP/GO LITE INSTRUCTIONS" before proceeding.
b.Check the polarity of the battery post. The POSITIVE (POS, P, +) battery post usually has a larger diameter than the NEGATIVE (NEG, N,
c.Attach at least a 24 inch long
d.Connect the POSITIVE (RED) charger clamp to the POSITIVE (POS, P, +) post of the battery.
e.Touch the contact button of the STOP/GO LITE to the free end of the battery cable. If the red light comes on, reverse the connections to the battery and retest. When the green light comes on, position yourself and the free end of the cable as far away from the battery as possible, then connect the NEGATIVE (BLACK) charger clamp to the free end of cable.
f.Do not face the battery when making the final connection.
g.When disconnecting the charger, always do so in reverse sequence of connecting procedure, and break the first connection while standing as far away from the battery as practical.
h.A marine (boat) battery must be removed and charged on shore. To charge it on board requires equipment specially designed for marine use.
20.GROUNDING AND AC POWER CORD CONNECTION INSTRUCTIONS
The charger should be grounded to reduce the risk of electric shock. This | GROUNDED |
| GROUNDING METHODS |
|
charger is equipped with an electric cord having an equipment grounding |
| ADAPTER |
| |
OUTLET |
| ADAPTER | ||
conductor and a grounding plug. The plug must be plugged into an outlet that |
|
|
| |
|
|
|
| |
is properly installed and grounded in accordance with all local codes and |
|
| COVER OF GROUNDED |
|
ordinances. |
|
| OUTLET BOX |
|
|
|
| (C) | |
DANGER. Never alter the AC cord or plug provided - if it will not fit the |
| (A) | (B) | GROUNDING |
| MEANS | |||
outlet, have a proper outlet installed by a qualified electrician. Improper |
|
|
| |
|
|
|
|
connection can result in a risk of an electric shock. This battery charger is for use on a nominal
2