Installation (continued)
DANGER!
RISK OF PRODUCT DAMAGE AND SERIOUS PERSONAL INJURY!
The battery module compartment's wheels are not designed to provide
4 | Remove the battery module compartment's access panel. | 4 |
|
5 | Add internal battery packs, fuse block brackets and fuses to the standalone |
|
|
| battery module compartment. See “Adding or Replacing Internal Batteries” in |
|
|
| the UPS system's owner's manual. Ensure that the battery cable connectors are |
|
|
| not covered. |
|
|
6 | Using the included cable A , connect one end to the UPS system's external | 6 |
|
| battery cable connector B and the other end to the SUBF2030's external |
| A |
| battery cable connector C . To reach the internal connectors, run the cable |
|
|
| through the access slots located on the bottom panel of the UPS system and |
| B |
| SUBF2030 (not shown). To keep the cable away from the front of the UPS, run |
| A |
| it behind the front caster wheels of the UPS system and SUBF2030 D . If the |
|
|
| mounting brackets are not attached to the floor, ensure the rear caster wheels |
| C |
| are locked to prevent the wheels from running over the cable. |
| |
|
|
| |
7 | OPTIONAL | D | A |
| compartments in a |
| D |
| Using the included cable A , connect one end to the external battery cable |
|
|
| connector B located in the upper, middle section of the SUBF2030 located |
|
|
| closest to the UPS system. Connect the other end of the included cable to the | 7 |
|
| external battery cable connector C located in the lower, right corner of the |
| |
| SUBF2030 located farthest from the UPS system. |
|
|
| SUBF2030 compartments, |
|
|
| SUBF2030 models on top of each other. |
|
|
8 | Replace battery module compartment's access panel. |
| A |
|
| ||
|
|
| C |
9 | Return the UPS system to Normal Mode or completely turn it on, depending on | B |
|
| the procedure you followed in step 1. See UPS system owner's manual for |
| |
| instructions. |
|
|
|
|
| A |
Warranty & Warranty Registration
LIMITED WARRANTY
Seller warrants this product, if used in accordance with all applicable instructions, to be free from original defects in material and workmanship for a period of 2 years (except U.S., Canada and Mexico: 1 year) from the date of initial purchase. If the product should prove defective in material or workmanship within that period, Seller will repair or replace the product, in its sole discretion. Service under this Warranty includes parts and Tripp Lite service center labor. Onsite service plans are available from Tripp Lite through authorized service partners (in most areas). Contact Tripp Lite Customer Service at (773)
THIS WARRANTY DOES NOT APPLY TO NORMAL WEAR OR TO DAMAGE RESULTING FROM ACCIDENT, MISUSE, ABUSE OR NEGLECT. SELLER MAKES NO EXPRESS WARRANTIES OTHER THAN THE WARRANTY EXPRESSLY SET FORTH HEREIN. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ALL IMPLIED WARRANTIES, INCLUDING ALL WARRANTIES OF MERCHANTABILITY OR FITNESS, ARE LIMITED IN DURATION TO THE WARRANTY PERIOD SET FORTH ABOVE; AND THIS WARRANTY EXPRESSLY EXCLUDES ALL INCIDENTAL AND CONSEQUENTIAL DAMAGES. (Some states do not allow limitations on how long an implied warranty lasts, and some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you. This Warranty gives you specific legal rights, and you may have other rights which vary from jurisdiction to jurisdiction).
Tripp Lite; 1111 W. 35th Street; Chicago IL 60609; USA
WARNING: The individual user should take care to determine prior to use whether this device is suitable, adequate or safe for the use intended. Since individual applications are subject to great variation, the manufacturer makes no representation or warranty as to the suitability or fitness of these devices for any specific application..
WARRANTY REGISTRATION
Visit www.tripplite.com/warranty today to register the warranty for your new Tripp Lite product. You'll be automatically entered into a drawing for a chance to win a FREE Tripp Lite product!* * No purchase necessary. Void where prohibited. Some restrictions apply. See website for details.
Regulatory Compliance Identification Numbers
For the purpose of regulatory compliance certifications and identification, your Tripp Lite product has been assigned a unique series number. The series number can be found on the product nameplate label, along with all required approval markings and information. When requesting compliance information for this product, always refer to the series number. The series number should not be confused with the marking name or model number of the product.
Tripp Lite follows a policy of continuous improvement. Product specifications are subject to change without notice.
200701108