Tile Saw Safety Warnings
1.
DANGER: Keep hands away from cutting area and the blade. If both hands are holding the saw, they cannot be cut by the blade.
2.Do not use to cut metal.
3.Do not use for curve or angle cutting. Doing so may damage Tile Saw blade.
4.Do NOT use with a “wet” attachment or attempt to lubricate blade.
5.Do not use with a grinding wheel attachment; only use a diamond cutting disc.
6.Do not use damaged or cracked cutting disc.
7.Do not start Tile Saw with cutting blade already set against tile surface.
8.Do not reach underneath the workpiece. The guard cannot protect you from the blade below the workpiece.
9.Adjust the cutting depth to the thickness of the tile being cut. Less than a full tooth of the blade teeth should be visible below the workpiece.
10.Never hold tile being cut in your hands or across your leg. Secure the tile to a stable platform. It is important to support the work properly to minimize body exposure, blade binding, or loss of control.
11.Hold power tool by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring or its own cord.
Contact with a″ live″ wire will also make exposed metal parts of the power tool ″live″ and shock the operator.
12.Always use blades with correct size and shape (diamond versus round) of arbor holes. Blades that do not match the mounting hardware of the saw will run eccentrically, causing loss of control.
13.Never use damaged or incorrect blade washers or bolt. The blade washers and bolt were specially designed for your saw, for optimum performance and safety of operation.
14.Causes and Operator Prevention of Kickback:
•Kickback is a sudden reaction to a pinched, bound or misaligned saw blade, causing an uncontrolled saw to lift up and out of the workpiece toward the operator;
•When the blade is pinched or bound tightly by the kerf closing down, the blade stalls and the motor reaction drives the unit rapidly back toward
the operator;
•If the blade becomes twisted or misaligned in the cut, the teeth at the back edge of the blade can dig into the top surface of the wood causing the blade to climb out of the kerf and jump back toward the operator.
Kickback is the result of saw misuse and/or incorrect operating procedures or conditions and can be avoided by taking proper precautions as given below:
a.Maintain a firm grip with both hands on the saw and position your arms to resist kickback forces. Position your body to either side
of the blade, but not in line with the blade.
Kickback could cause the saw to jump backwards, but kickback forces can be controlled by the operator, if proper precautions are taken.
b.When blade is binding, or when interrupting a cut for any reason, release the trigger and hold the saw motionless in the material until the blade comes to a complete stop. Never attempt to remove the saw from
the work or pull the saw backward while the blade is in motion or kickback may occur. Investigate and take corrective actions to eliminate the cause of blade binding.
c.When restarting a saw in the workpiece, center the saw blade in the kerf and check that saw teeth are not engaged into the material. If saw blade is binding, it may walk up or kickback from the workpiece as the saw is restarted.
d.Support large panels to minimize the risk of blade pinching and kickback. Large panels tend to sag under their own weight. Supports must
be placed under the panel on both sides, near the line of cut and near the edge of the panel.
e.Do not use dull or damaged blades.
Unsharpened or improperly set blades produce narrow kerf causing excessive friction, blade binding and kickback.
f.Blade depth and bevel adjusting locking levers must be tight and secure before making cut. If blade adjustment shifts while cutting, it may cause binding and kickback.
g.Use extra caution when making a ″plunge cut″ into existing walls or other blind areas. The protruding blade may cut objects that can cause kickback.
15.Check lower guard for proper closing before each use. Do not operate the saw if lower guard does not move freely and close instantly. Never clamp or tie the lower guard into the open position. If saw is accidentally dropped, lower guard may be bent. Raise the lower guard with the retracting handle and make sure it moves freely and does not touch the blade
or any other part, in all angles and depths of cut.
Page 4 | For technical questions, please call | SKU 68298 |