Porter-Cable 7335 instruction manual Carton Contents Functional Description

Page 9

MOTOR

Many Porter-Cable tools will operate on either D.C., or single phase 25 to 60 cycle A.C. current and voltage within plus or minus 5 percent of that shown on the specification plate on the tool. Several models, however, are designed for A.C. current only. Refer to the specification plate on your tool for proper voltage and current rating.

Do not operate your tool on a current on which the voltage is not within correct limits. Do not operate tools rated A.C. only on D.C. current. To do so may seriously damage the tool.

EXTENSION CORD SELECTION

If an extension cord is used, make sure the conductor size is large enough to prevent excessive voltage drop which will cause loss of power and possible motor damage. A table of recommended extension cord sizes will be found in this section. This table is based on limiting line voltage drop to 5 volts (10 volts for 230 volts) at 150% of rated amperes.

If an extension cord is to be used outdoors, it must be marked with the suffix W- A or W following the cord type designation. For example – SJTW-A to indicate it is acceptable for outdoor use.

RECOMMENDED EXTENSION CORD SIZES FOR USE WITH PORTABLE ELECTRIC TOOLS

Length of Cord in Feet

 

115V

25 Ft.

50 Ft.

100 Ft.

150 Ft.

200 Ft.

250 Ft.

300 Ft.

400 Ft.

500 Ft.

 

230V

50 Ft.

100 Ft.

200 Ft.

300 Ft.

400 Ft.

500 Ft.

600 Ft.

800 Ft.

1000 Ft.

 

 

 

 

 

 

 

 

 

 

 

 

0-2

18

18

18

16

16

14

14

12

12

 

 

 

 

 

 

 

 

 

 

 

Rating

2-3

18

18

16

14

14

12

12

10

10

3-4

18

18

16

14

12

12

10

10

8

 

 

 

 

 

 

 

 

 

 

4-5

18

18

14

12

12

10

10

8

8

Ampere

5-6

18

16

14

12

10

10

8

8

6

6-8

18

16

12

10

10

8

6

6

6

 

 

 

 

 

 

 

 

 

 

8-10

18

14

12

10

8

8

6

6

4

Nameplate

 

 

 

 

 

 

 

 

 

 

10-12

16

14

10

8

8

6

6

4

4

12-14

16

12

10

8

6

6

6

4

2

 

 

 

 

 

 

 

 

 

 

14-16

16

12

10

8

6

6

4

4

2

 

 

 

 

 

 

 

 

 

 

 

16-18

14

12

8

8

6

4

4

2

2

 

18-20

14

12

8

6

6

4

4

2

2

 

 

 

 

 

 

 

 

 

 

 

SAVE THESE INSTRUCTIONS!

CARTON CONTENTS

This tool is shipped with an auxiliary handle, an abrasive disc, a 9/16" wrench, a spacer, an instruction manual, and a parts list.

FUNCTIONAL DESCRIPTION

FOREWORD

The Porter-Cable Random Orbit Polisher performs various tasks, including polishing, rubbing, and general cleaning jobs. Used as a Random Orbit Sander, the tool provides rapid stock removal with 80 to 100 grit paper and swirl-free finishing with 120 to 150 grit paper.

9

Image 9
Contents Español Página Française Important Safety Instructions Table of ContentsCalifornia Proposition Safety Guidelines DefinitionsGeneral Safety Rules General Safety Rules Additional Specific Safety Rules Symbol Definition Additional Safety Rules for Paint Removal Carton Contents Functional Description Operation AssemblyAuxiliary Handle To Start and Stop ToolINSTALLING/REMOVING Abrasive Disc Using the PolisherChanging the BACK-UP PAD Using the SanderKeep Tool Clean Troubleshooting MaintenanceFailure to Start LubricationAccessories ServiceWarranty Replacement Parts Service and RepairsCanadian PORTER-CABLE Delta Service Centers