Porter-Cable CPFC2TV3525VP instruction manual Problem Cause Correction

Page 14

PROBLEM

CAUSE

CORRECTION

 

 

 

Pressure reading on

It is normal for “some”

If there is an excessive amount of

the regulated

pressure drop to occur.

pressure drop when the accessory

pressure gauge

 

is used, adjust the regulator

drops when an

 

following the instructions on page

accessory is used.

 

7.

 

 

NOTE: Adjust the regulated

 

 

pressure under flow conditions

 

 

(while accessory is being used).

 

 

 

Motor will not run or

Motor overload protection

Let motor cool off and overload

restart.

switch has tripped.

switch will automatically reset.

 

Tank pressure exceeds

Motor will start automatically when

 

pressure switch “cut-in”

tank pressure drops below “cut-in”

 

pressure.

pressure of pressure switch.

 

Wrong gauge wire or length of

Check for proper gauge wire and

 

extension cord.

cord length.

 

Check valve stuck open.

Remove and clean, or replace.

 

Loose electrical connections.

Check wiring connection inside

 

 

pressure switch and terminal box

 

 

area.

 

Possible defective motor or

Contact an Authorized Warranty

 

starting capacitor.

Service Center for inspection or

 

 

replacement, if necessary.

 

Paint spray on internal motor

Have checked by an Authorized

 

parts.

Warranty Service Center. Do not

 

 

operate the compressor in the paint

 

 

spray area. See flammable vapor

 

 

warning.

 

Fuse blown, circuit breaker

1. Check fuse box for blown fuse

 

tripped.

and replace, if necessary. Reset

 

 

circuit breaker. Do not use a

 

 

fuse or circuit breaker with

 

 

higher rating than that specified

 

 

for your particular branch circuit.

 

 

2. Check for proper fuse; only time

 

 

delay fuses are acceptable.

 

 

3. Check for low voltage

 

 

conditions and/or proper

 

 

extension cord.

 

 

4. Disconnect the other electrical

 

 

appliances from circuit or

 

 

operate the compressor on its

 

 

own branch circuit.

 

Pressure release valve on

Bleed the line by pushing the lever

 

pressure switch has not

on the pressure switch to the “off”

 

unloaded head pressure.

position; if the valve does not open,

 

 

replace it.

 

 

 

14-ENG

Image 14
Contents Instruction Oilfree Manual Compressor Read and Follow ALL Instructions Safety Guidelines DefinitionsImportant Safety Instructions Hazard Risk of Explosion or Fire What can Happen HOW to Prevent ITWhat can Happen HOW to Prevent IT Risk of BurstingRisk of Electrical Shock What can Happen HOW to Prevent IT Risk from Flying Objects What can Happen HOW to Prevent ITRisk to Breathing What can Happen HOW to Prevent IT Risk of Falling What can Happen HOW to Prevent IT Risk from Moving Parts What can Happen HOW to Prevent ITRisk of Burns What can Happen HOW to Prevent IT Risk of Property Damage When Transporting CompressorDuty Cycle SpecificationsGlossary Model NoAir Compressor Pump not shown Description of OperationAir Intake Filter not shown This filter is Lubrication and Oil InstallationLocation of the Air Compressor Extension CordsImproper grounding can result Electrical shock Voltage and Circuit ProtectionPiping Daily Start-Up Checklist BREAK-IN ProceduresOperating Procedures Procedure Air Filter Inspection and Replacement Maintenance Service Instructions Safety Valve InspectionStorage Check Valve ReplacementMotor Wiring Diagram MotorTroubleshooting Guide OVER-TIGHTENProblem Cause Correction 15-ENG Accessories FILTERS, REGULATORS, Lubricators17-ENG Limited Warranty This Warranty is not Transferable and does not Cover