Porter-Cable 36-729 instruction manual Common Sawing Operations, Cross-Cutting

Page 19

MACHINE USE

COMMON SAWING OPERATIONS

Common sawing operations include ripping and crosscutting plus a few other standard operations of a fundamental nature. As with all power machines, there is a certain amount of hazard involved with the operation and use of the machine. Using the machine with the respect and caution demanded as far as safety precautions are concerned, will considerably lessen the possibility of personal injury. However, if normal safety precautions are overlooked or completely ignored, personal injury to the operator can result. The following information describes the safe and proper method for performing the most common sawing operations.

THE USE OF ATTACHMENTS AND ACCESSORIES NOT RECOMMENDED BY DELTA MAY RESULT IN THE RISK OF INJURY TO THE USER OR OTHERS.

CROSS-CUTTING

Cross-cutting requires the use of the miter gage to position and guide the work. Place the work against the miter gage and advance both the gage and work toward the saw blade, as shown in Fig. 50. The miter gage may be used in either table slot. When bevel cutting (blade tilted), use the table groove that does not cause interference of your hand or miter gage with the saw blade guard.

Start the cut slowly and hold the work firmly against the miter gage and the table.

ONE OF THE RULES IN RUNNING A SAW IS THAT YOU NEVER HANG ONTO OR TOUCH THE PART OF THE WORKPIECE THAT WILL BE

CUT OFF. Hold the supported piece, not the free piece that is cut off. The feed in cross-cutting continues until the work is cut in two, and the miter gage and work are pulled back to the starting point. Before pulling the work back, it is good practice to give the work a little sideways shift to move the work slightly away from the saw blade. Never pick up any short length of free work from the table while the saw is running. While blade is running, never touch a cut-off piece unless it is at least a foot long.

For added safety and convenience the miter gage can be fitted with an auxiliary wood-facing (C), as shown in Fig. 51, that should be at least 1 inch higher than the maximum depth of cut, and should extend out 12 inches or more to one side or the other depending on which miter gage slot is being used. This auxiliary wood-facing (C) can be fastened to the front of the miter gage by using two wood screws (A) through the holes provided in the miter

gagebodyandinto the wood-facing.

When using the block (B) Fig. 52, as a cut- off gage, it is very important that the rear end of the block be positioned so the work piece is clear of the block before it enters the blade.

NEVER USE THE FENCE AS A CUT-OFF GAGE WHEN CROSS-CUTTING.

When cross-cutting a number of pieces to the same length, a BLOCK OF WOOD (B), can be clamped to the fence and used as a cut-off gage as shown in Fig. 52. It is important that this block of wood always be positioned in front of the saw blade as shown. Once the cut-off length is determined, secure the fence and use the miter gage to feed the work into the cut. This block of wood allows the cut-off piece to move freely along the table surface without binding between the fence and the saw blade, thereby lessening the possibility of kickback and injury to the operator.

Fig. 50

A

A

C

Fig. 51

B

Fig. 52

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Cabinet Saw Important Safety Instructions Table of ContentsCalifornia Proposition Safety Guidelines DefinitionsStay ALERT, Watch What YOU are Doing General Safety RulesUSE of this Tool can Generate and Disburse Dust or Other Failure to Follow These Rules MAY Result in Serious Injury Additional Specific Safety RulesMotor Specifications Power ConnectionsGrounding Instructions Functional Description Carton ContentsAssembly Tools Required AssemblyAttaching Handwheels Blade Tilting Lock KnobExtension Wings Blade Guard and Splitter Assembly Insert threaded end of support rod / splitter bracket Page Table Insert a should Always be Level with the Table Motor CoverBlade Raising Handwheel Locking Switch OFF PositionOperation Starting and Stoping the SAWDisconnect Machine from Power Source Replacing Belts Adjusting Belt TensionChanging the SAW Blade Adjusting 90 and 45 Degree Positive Stops Adjusting Table Insert Adjusting TableMiter Gage Operation and Adjustment Common Sawing Operations Never USE the Fence AS a CUT-OFF Gage When CROSS-CUTTINGCROSS-CUTTING Constructing a Push Stick RippingGuard Removed for CLARITY. Always USE the Guard Using Moulding Cutterhead Accessory Dado Head Using Auxiliary Wood Facing on RIP Fence TroubleshootingConstructing a Featherboard Constructing a Push Stick PushstickWarranty MaintenanceService AccessoriesPage Page Canadian PORTER-CABLE Delta Service Centers
Top Page Image Contents