Multiquip MP1415E, MP1420E, MP1455H manual Material is to be cut

Page 17

CONTROLS AND COMPONENTS

Figure 2 shows the location of the basic controls or components for the MP1 saw. Listed below is a brief explanation of each control or component.

1.

Ruler Backstop – When cutting, place material against

 

backstop. Use measurement rail (ruler) to determine where

 

material is to be cut.

2.

Water Tray – When wet cutting is required, fill with clean

 

fresh water.Make sure submersible is totally immersed in

 

water.

3.

Cutting Head Handle – Grab hold of this handle to move

 

the cutting blade head either up or down. To move the

 

cutting head, release the mounting plate release/lock lever.

4.

Carrying Handle (Head) – Grip this handle (front) to lift

 

the mounting plate.

5.

Blade Guard – Protects the user from the cutting blade.

 

NEVER operate the saw with the blade guard removed.

6.

Power ON/OFF Box – This box is used on electric

 

models saws only. To turn on the saw place in the ON

 

position. Place in the OFF position to shut-down the saw.

7.

V-belt Cover – Remove this cover to access the drive V-

 

belt. NEVER operate the saw with theV-belt cover removed.

8.

Mounting Plate Release/Lock Lever – Push this lever

 

backwards to release the mounting plate.This will allow

 

the cutting head to move either up or down. Push the lever

 

forward to lock the mounting plate in place.

9.

Electric Motor/Conduit Box– This unit uses 2 different

 

types of electric motors and voltages (seeTable 2).Always

 

make sure the voltage selector switch has been set to the

 

correct position for the voltage being supplied to the motor.

 

Plug the water pump (electric models only) power cord

 

into the AC receptacle located on the conduit box.

10.

Mounting Plate – Supports the electric motor/gasoline

 

engine. Plate has slotted holes for horizontal (right-side)

 

and vertical (left-side) adjustment of cutting head.

11.

Carrying Handle (Head) – Grip this handle (rear) to lift

 

the mounting plate.

12. Tie Rod – The tie rod length has been set at the factory for best blade guard position for the majority of the cutting that will be done.

13. Spring Tensioner – Allows for an easy up and down movement of the mounting plate.

14. Mounting Plate Lock/Release Knobs – Turn knob (2) clockwise to release the mounting plate. Turn counter- clockwise to tighten.

15. Stopper – Place stopper in tray when filling with water.

16. Carrying Handle (Tray) – Grip this handle (right-side) to trasport the saw.

17. Electric Water Pump – For best results place the pump between the splash shield and the rear of the water tray. This is for electric models only. Plug water pump power cord into AC receptacle on electric motor conduit box. NEVER run pump dry.Pump must be immersed in water.

18. Spindle Bolt/Outside Blade Flange – When mounting of the cutting blade is required, remove the spindle bolt and outside blade flange. Align cutting blade with inside flange arbor and reassemble spindle and outside blade flange.

19. Splash Guard – Keeps water and debris from leaving the water tray.

20. Carrying Handle (Tray) – Grip this handle (left-side) to trasport the saw.

21. MechanicalWater Pump – This pump is used on gasoline models only. Saw is shipped from the factor for wet cutting applications (pump handle down). Place pump handle upwards to disengage pump. NEVER run pump dry.

22. Engine – The gasoline model saws uses a 5.5 HP Honda GX160, 4-stroke, OHV, single cylinder, air cooled gasoline engine.

23. V-belt Cover (Gasoline Only) – Remove this cover to access the engine shaft-sideV-belt.NEVER operate the saw with the V-belt cover removed.

24. Water Lines – Replace the clear vinyl tubing water lines when they become brittle, worn or clogged. Water kits are available through your dealer.

25. Priming Bulb – Squeeze this bulb to prime the mechanical water pump (gasoline models only).

26. BladeWrench – Use this tool to mount and remove cutting blade.

27. Strainer – For best results place the strainer between the splash shield and the rear of the water tray. This is for gasoline models only.NEVER run pump dry.Strainer must be immersed in water.

28. Miter Box – For angled cuts, place the lip of the miter box on the measurement rail with the threaded thumb knob facing you and tighten.

MP1 — OPERATION AND PARTS MANUAL — REV. #3 (03/29/10) — PAGE 17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Models Proposition 65 Warning Respiratory Hazards SILICOSIS/RESPIRATORY Warnings Silicosis WarningDrawings Table of ContentsOrdering parts has never been easier Parts Ordering ProceduresSafety Message Alert Symbols Not Do not Never AlwaysRules for Safe Operation SafetySafety Gasoline Powered Engines Blade Safety Safety Electric Powered ModelsGeneral Safety Emergencies SAW Maintenance CleaningSawtransportation Safety MP1 Operation and Parts Manual REV. #3 03/29/10 MP1 SAW Specifications Specifications SAW/ENGINEDimensions DimensionsGeneral Information MP1 Operation and Parts Manual REV. #3 03/29/10 MP1 Saw Electric/Gasoline Controls and ComponentsMaterial is to be cut Electric Motor Components MP1 Electric Motor ComponentsInitial SERVICING-GASOLINE Engine MP1 Engine ComponentsConveyor Cart Placement PRE-SETUP ElectricPRE-SETUP SAW Blade Definitions Figure Blade InstallationSAW Blades Motor Voltage Connectingthe Power FigureDRY Cutting Electric Saws only Gfci ReceptacleWET Cutting Gasoline only PRE-SETUP GasolineDRY Cutting Gasoline only Fuel Check Before StartingEngine OIL Check START-UP Electric Motor Operation ElectricWait for the cutting blade to stop rotating Shutdown ProcedureSTART-UP Gasoline Engine Operation GasolineStopping Do not Never Throttle LeverNever Basic Maintenance Maintenance SAWMaintenance Horizontal Adjustment Vertical AdjustmentCutting Head Alignment Blade Bearing Lubrication CareEnginemaintenance MP1 Maintenance EngineDaily EngineaircleanerWeekly Engine OILElectric MotorWiring Diagram Wiring Diagram Electric MotorMP1 Operation and Parts Manual REV. #3 03/29/10 Blade Troubleshooting Troubleshooting BladeTroubleshooting Electric Motor Troubleshooting Electric MotorEngine Troubleshooting Troubleshooting Gasoline EngineEngine Troubleshooting Explanation of Code in Remarks Column Sample Parts ListMP1 Masonry SAW 1TO 3 Units Electric Motor Models Suggested Spare PartsName Plate and Decals Part Name QTY Remarks Tray Assy Part Name QTY Cart Assy Insert Motor Plate & Shaft Assy GRIP, Hand Engine Honda 5.5 H.P Engine Honda 5.5 H.P Electric Motor Part Name Water Pump ASSY. Gasoline only PULLEY, Water Pump Support Stand Assy Stand Assembly Outer Honda GX160K1QXC9 AIR Cleaner Assy GASKET, Elbow Honda GX160K1QXC9 Camshaft Assy Part Name QTY. Remarks Honda GX160K1QXC9 Carburetor Assy Gasket SET Honda GX160K1QXC9 Control Assy ARM, Governor Honda GX160K1QXC9 Crankcase Cover Assy GASKET, OIL Filler CAP Honda GX160K1QXC9 Crankshaft Assy Crankshaft Q- Type Honda GX160K1QXC9 Cylinder Barrel Assy WEIGHT, Governor Honda GX160K1QXC9 Cylinder Head Assy GUIDE, Valve OS Optional Honda GX160K1QXC9 FAN Cover Assy COVER, FAN *R8* Bright RED Honda GX160K1QXC9 Flywheel Assy FAN, Cooling Honda GX160K1QXC9 Fuel Tank Assy RUBBER, Supporter 107MM Honda GX160K1QXC9 Ignition Coil Assy Coil ASSEMBLY, Ignition Honda GX160K1QXC9 Muffler Assy MUFFLER, Silent Honda GX160K1QXC9 Piston and Rings Assy Ring SET, Piston Standard Honda GX160K1QXC9 Recoil Starter Assy REEL, Recoil Starter Honda GX160K1QXC9 Gasket KIT Assy No ART WorkGASKET, Cylinder Head Cover Honda GX160K1QXC9 Labels Assy Emblem Terms and Conditions of Sale Parts MP1 Operation and Parts Manual REV. #3 03/29/10 HERE’S HOW to GET Help

MP1420E, MP1415E, MP1455H specifications

The Multiquip MP1455H, MP1415E, and MP1420E are part of Multiquip’s line of high-performance concrete and masonry saws, designed to cater to the diverse needs of the construction industry. Each model offers unique features and technologies tailored to enhance productivity, efficiency, and user comfort.

Starting with the MP1455H, this saw is powered by a robust Honda GX390 engine, delivering reliable performance for heavy-duty cutting tasks. It boasts a 14-inch cutting blade capacity, enabling users to cut through various materials with ease. The MP1455H is equipped with a user-friendly depth control system, allowing for precise cuts and adjustments on the fly. Its rugged frame is constructed with durable materials, ensuring longevity even in the most challenging job site conditions.

The MP1415E is an electric-powered saw designed for quieter operation without compromising power. It features a 15-inch blade capacity, making it suitable for a variety of applications such as asphalt, concrete, and masonry. This model is particularly appreciated for its low vibration technology, significantly reducing operator fatigue. Additionally, the MP1415E includes an integrated water system that promotes clean cutting and minimizes dust, promoting a healthier work environment.

The MP1420E rounds out the lineup with enhanced features for improved power and efficiency. Like the MP1415E, this model is electric-powered, but it accommodates a 20-inch blade, making it ideal for larger cutting tasks. The saw is designed with a heavy-duty steel frame that provides stability and minimizes flex during operation. Featuring advanced electronic controls, the MP1420E allows users to monitor performance metrics easily, making it suitable for both experienced and novice operators.

All three models incorporate advanced cooling systems to prolong blade life and maintain optimal performance. Their compact designs ensure ease of transport, and they are suitable for both indoor and outdoor applications, providing versatility in various job sites.

In summary, the Multiquip MP1455H, MP1415E, and MP1420E concrete and masonry saws are engineered to meet the rigorous demands of the construction industry. With powerful engines, user-friendly features, and advanced technologies, these saws deliver exceptional performance, reliability, and ease of use.
Top Page Image Contents