USING THE
Battery State of Charge |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
| |||||||||
|
|
|
|
|
|
|
|
| to Port 1, Chan |
| |||||||
|
|
|
|
| Xmtr |
|
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
| Power |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Supply |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Output |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Power | 5VDC Powered |
|
|
|
|
|
|
|
|
|
|
| mV Output |
| ||
| Transducer |
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
| Signal to |
| |||
| Supply | (mV Output) |
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
| Port 1, Chan A | ||||
| Output |
|
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Charger |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Input | Com |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
+ Control | mon |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
_ Input |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 11 12 | |
|
|
|
|
|
|
|
|
|
|
|
| Port 1 |
|
|
|
| |
| 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 11 12 |
|
|
| ||||
Controlled by one of the |
|
|
| ||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
standard |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Outputs. |
| R1 |
| R2 | DO1 | DO3 | GND | GPDI Input |
|
| |||||||
|
|
|
|
|
| DO2 |
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
| 1 | 2 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 11 | 12 |
Port 2 | |
Strip Adapter (TSA) |
Figure 3: RPS-1 Control Wiring
The MODE switch (bottom or eighth switch) should be set for the desired operation, AUTO or ON. AUTO mode configures the supply to cycle ON and OFF per the state of the control signal coming from an external device
The power supply outputs are internally current limited and protected from shorts. Current limiting occurs at approximately 250 mA. If loads approaching this current level are connected, the output voltage should be tested with a
The MAIN POWER SWITCH must be set in the 12VDC or the 24VDC position for the power supplies to function. For optimum battery life, set the MAIN POWER SWITCH at 12VDC if neither power supply
Omega Engineering Inc. | 4 | Stamford, CT |