Parkside PFS 100 B2 manual Service centre, Maintenance and cleaning Warranty

Page 11

Bringing into use / Maintenance and cleaning / Service centre / Warranty

and stop the spraying process approximately 10 cm outside the surface to be sprayed. NOTE: The distance between the nozzle and the workpiece depends on the material being sprayed (approx. 20 to 35 cm spraying dis- tance, depending on the spray cone and the desired amount of material to be applied). Use the device in a horizontal orientation only (as shown in Fig. D).

Carry out a trial in each case to determine the most effective spraying distance.

Start with a longer distance.

3.Spray corners or small decorative details first using short bursts of spray.

Then go on to the actual spraying process.

4.The spray process should follow the sequence shown in Fig. E – keep the spray gun moving parallel to the surface

Do not incline the spray gun

Move the spray gun at a constant speed

Apply the sprayed medium as thinly as possible

The layer(s) of sprayed medium need(s) to be allowed to dry for some time before you apply the next coat Fig. F) at right angles to the previous coat.

5.Do not allow the paint cup 7 to empty com- pletely while spraying – drops may form!

Cleaning instructions:

1.Unscrew the attachment screw 1 , see Fig. A.

2.Take off the pump housing 10 downwards.

3.Unscrew nozzle 8 and remove the suction- pressure valve 9 .

4.Take the pump piston 4 and spring 5 out of the pump housing 10 .

5.Clean parts 4 , 5 , 8 , 9 with thinners.

6.Fit the components back in reverse order.

TIP: After use or cleaning, hang up the electrical power tool from the metal stirrup 14 .

Service centre

Have your electrical power tool repaired only by qualified specialist personnel using original man- ufacturer parts only. This will ensure that your electrical power tool remains safe to use. If the plug or mains lead needs to be replaced, always have the replacement carried out by the manufacturer or its service centre. This will ensure that your electrical power tool remains safe to use.

Maintenance and cleaning

 

Warranty

General advice:

1.

 

 

 

 

Pull out the mains plug be-

 

fore you carry out any tasks on the spray gun.

 

Do the same when you take a break from spraying.

2.

After each use, spray thinners (in the open

 

air only – danger of explosion!) or

 

water through the device.

3.

To protect from rust after cleaning, you can

 

spray sewing machine oil through the device.

4.

 

 

 

 

DANGER TO LIFE

 

THROUGH ELECTRIC SHOCK! Never im-

 

merse the device in the cleaning medium.

5.

Never use inflammable solvents to clean the

 

device.

6.

Use a dry cloth to clean the housing. Never

 

use petrol, solvents or cleaning agents that

 

might attack plastic.

The warranty for this appliance is for 3 years from the date of purchase. The ap- pliance has been manufactured with care and meticulously examined before deliv- ery. Please retain your receipt as proof of purchase. In the event of a warranty claim, please make contact by telephone with our Service Department. Only in this way can a post-free despatch for your goods be assured.

The warranty covers only claims for material and maufacturing defects, but not for transport damage, for wearing parts or for damage to fragile compo- nents, e.g. buttons or batteries. This product is for pri- vate use only and is not intended for commercial use.

GB/IE 11

Image 11
Contents Paint Spray GUN PFS 100 B2 GB / IE Page Page Table of contents Proper use Features and equipmentIntroduction Paint spray gun PFS 100 B2 IntroductionElectrical safety Technical dataWorkplace safety Careful handling and use of electrical power tools General safety advice for electrical power toolsPersonal safety Remeasure the DIN-seconds value Additional safety advice for paint spray gunsDIN-sec / Viscosity Preparing the sprayed mediumSelecting the nozzle Advice on use / Bringing into useSwitching on / OFF Preparing the surface to be sprayedMaintenance and cleaning Warranty Service centreEnvironmental compatibility and disposal of materials Warranty / DisposalIAN IAN DisposalDeclaration of Conformity Manufacturer Declaration of Conformity / ManufacturerPage Arbeitshinweise InhaltsverzeichnisEinleitung Allgemeine Sicherheitshinweise für ElektrowerkzeugeBestimmungsgemäßer Gebrauch EinleitungFarbspritzpistole PFS 100 B2 AusstattungElektrische Sicherheit Technische DatenArbeitsplatz-Sicherheit Zweckentfremden Sie das Kabel nicht, um das Elektro Allgemeine Sicherheitshinweise für ElektrowerkzeugeSicherheit von Personen Verwendung und Behandlung des ElektrowerkzeugsDIN-Sec / Viskosität Ergänzende Sicherheitshinweise für FarbspritzpistolenDüse wählen Arbeitshinweise / InbetriebnahmeSpritzgut vorbereiten Spritzfläche vorbereitenWartung und Reinigung Inbetriebnahme / Wartung und Reinigung / ServiceService SpritzvorgangWerfen Sie Elektrowerkzeuge nicht in den Hausmüll Garantie / EntsorgungGarantie IAN EntsorgungKonformitätserklärung Hersteller Entsorgung / Konformitätserklärung / HerstellerKompernass Gmbh