Grizzly MODEL instruction manual Miter Gauge, To adjust the miter gauge

Page 27

Miter Gauge

The miter gauge for the Model G1023S Series has two setscrews in the miter bar which can be set to remove any loose movement between the miter bar and the T-slot.

To adjust the miter gauge:

1.Loosen or tighten the two miter bar setscrews (Figure 23) until the miter gauge slides freely in the slot, but has no loose movement.

2.Loosen the lock knob on the miter gauge and place a square against the face of the miter body and the miter bar.

3.Adjust the miter body until there is no space between the square and the miter bar.

4.Tighten the lock knob.

5.With the stop link (Figure 23) in the up posi- tion, loosen the jam nut and adjust the stop screw until it is seated against the stop link.

6.Loosen the setscrew on the left front side of the miter bar, adjust the pointer to 90û and retighten the setscrew.

7.To adjust to 45û, follow Steps 1-6while using an adjustable square.

8.After rotating the miter body from 45û to 90û and back a few times, double check your adjustments at both angles to ensure that you have accurately set your miter gauge.

Setscrew

Stop Link

Stop Screw

Jam Nut

Figure 23. Miter gauge adjustment points.

G1023S Series Heavy-Duty 10'' Table Saw

-25-

Page 26 Page 28
Image 27
Page 26 Page 28
Contents Model G1023S & G1023S110 HEAVY-DUTY Table SAWPage Table of Contents Safety Instructions For Power Tools Safety25ft 50ft 100ft Length AMP RatingAdditional Safety Instructions For Table Saws Following can help minimize kickbacks Avoiding Kickback Safety AccessoriesZero Clearance Table Inserts Push PaddlesFeatherboards Commentary Introduction110V Operation 220V Operation Circuit RequirementsModel G1023S Only Grounding Extension Cord Terms & Definitions Machine FeaturesMain Features Unpacking Piece Inventory SET UPG1023S Series component layout Bolt Hardware Recognition ChartWorking Clearance Clean UpSite Considerations Floor LoadBeginning Assembly Extension Wings Fence & Rails SwitchTo mount the switch Disconnect the machine from the power sourceMotor brace Cleanout Door Motor BraceGuard Bracket To install the blade guard assemblyTable Insert HandwheelBlade Guard/Splitter Saw BladeFront Support Blade Adjustment Bolt Miter Gauge To adjust the miter gaugeRecommended adjustment checklist Start Up RecommendedStarting the machine Blade Selection OperationsPage Crosscutting Typical ripping operation RippingSingle-blade dado cut Dado CuttingIf the cut is satisfactory, repeat with your fin- ish stock Rabbet cutting G1023S Series Heavy-Duty 10 Table Saw Rabbet CuttingRabbet cutting General MaintenanceLubricationTable BeltLubricate the areas indicated below every 12 months Belt deflection Date Approximate Hours Of Use Maintenance Performed 45˚ & 90˚ Stops Service AdjustmentsBlade Parallelism Page Trunnion mounting bolts Blade AlignmentPage G1023S Series Heavy-Duty 10 Table Saw G1023S Series Heavy-Duty 10 Table Saw Closure Motor Overall DimensionsCapacities ConstructionPage Page Complete Miter Gauge Symptom Possible Cause Corrective Action Troubleshooting GuideG1023S Series Heavy-Duty 10 Table Saw G1023S Series Heavy-Duty 10 Table Saw Warranty and Returns Warranty Card BOX BELLINGHAM, WA Grizzly INDUSTRIAL, INCCall Today For a Free Full Color Catalog
Related manuals
Manual 2 pages 987 b

MODEL specifications

The Grizzly MODEL represents a significant advancement in the realm of high-performance machinery, designed with a blend of robust engineering and cutting-edge technology. This model caters primarily to industrial applications, where reliability and efficiency are paramount.

One of the standout features of the Grizzly MODEL is its powerful engine, which boasts superior torque and horsepower. This capability allows it to perform demanding tasks with ease, making it suitable for a variety of heavy-duty operations. The engine is designed for fuel efficiency, ensuring that users not only benefit from increased performance but also reduced operational costs.

The Grizzly MODEL is also equipped with advanced drivetrain technology. The all-wheel-drive system enhances traction, significantly improving maneuverability on diverse terrains. Whether operating on rough, uneven ground or navigating through tight spaces, the Grizzly MODEL excels, ensuring it can handle any job site with precision.

In terms of safety, this model includes multiple features aimed at protecting the operator and surrounding personnel. It is built with reinforced structures, roll-cage protection, and advanced braking systems, all contributing to a safe work environment. Moreover, ergonomic controls enhance usability, allowing operators to maintain comfort and concentration throughout the working day.

Another key aspect of the Grizzly MODEL is its intuitive interface. The integrated control panel provides real-time data on performance metrics and diagnostics, enabling operators to make informed decisions quickly. This feature minimizes downtime by allowing for early detection of potential issues.

The durability of the Grizzly MODEL cannot be overlooked. It is constructed with high-grade materials that withstand harsh conditions, making it a long-term investment for businesses. The ability to withstand extreme weather and heavy workloads ensures that the equipment remains operational under the most challenging circumstances.

On the technology front, the Grizzly MODEL incorporates smart connectivity features, allowing users to monitor performance remotely. This connectivity facilitates seamless integration with other systems, enhancing overall operational efficiency.

In conclusion, the Grizzly MODEL stands out with its powerful engine, advanced drivetrain, robust safety features, intuitive interface, and impressive durability. It is an exceptional choice for industries requiring reliable, high-performance machinery that meets the demands of today's fast-paced work environments.
Top Page Image Contents