Bard CH5S1, CH4S1, CH3S1 Start UP, LOW Voltage Connections, Application, Wall Thermostat

Page 16

LOW VOLTAGE CONNECTIONS

These units use a grounded 24 volt AC low voltage circuit and require at least a 2 stage heating and a 2 stage cooling thermostat.

The “R” terminal is the hot terminal and the “C” terminal is grounded.

“G” terminal is the fan input.

“Y” terminal is the compressor Stage 1 input.

“Y1” terminal is the compressor Stage 2 input.

“B” terminal is the reversing valve input. The reversing valve must be energized for heating mode.

“R” terminal is 24 VAC hot.

“C” terminal is 24 VAC grounded.

“L” terminal is compressor lockout output. This terminal is activated on a high or low pressure trip by the electronic heat pump control. This is a 24 VAC output.

“W2” terminal is second stage heat (if equipped).

“O1” terminal is the ventilation input. This terminal energizes any factory installed ventilation option.

“E” terminal is the emergency heat input. This terminal energizes the emergency heat relay if equipped.

NOTE: For total and proper control using DDC, a total of 7 controlled outputs are required (6 if no ventilation system is installed). For proper system operation under Emergency Heat conditions where the compressor needs to be deactivated, the B-W2-E outputs need to be energized. Removing the Y (compressor) signal alone turns the compressor off, but does not activate the additional circuitry embedded in the heat pump for proper and complete operation.

LOW VOLTAGE CONNECTIONS

FOR DDC CONTROL

Fan Only

Energize G

Cooling Mode 1st Stage

Energize Y, G

Cooling Mode 2nd Stage

Energize Y, Y1, G

Heat Pump Heating 1st Stage

Energize Y, G, B

Heat Pump Heating 2nd Stage

Energize Y, Y1, G, B

3rd Stage Heating

Energize G, W2, Y, B, Y1

w/Heat Pump (if employed)

 

Ventilation

Energize G, O1

Emergency Heat

Energize B, W2, E, G

TABLE 4

WALL THERMOSTAT

Thermostat

Predominant Features

 

 

8403-049

2 stg. cool; 2 stg. heat

Programmable Electronic

(1F93-380)

Auto or Manual changeover

 

 

 

8403-052

2 stg. cool; 3 stg. heat

Programmable Electronic

 

 

Auto or Manual changeover

 

 

START UP

These units require R-410A refrigerant & Polyol Ester oil.

APPLICATION:

1.Use separate service and manufacturing equipment to avoid cross contamination of oil and refrigerants.

2.Use recovery equipment rated for R-410A refrigerant.

3.Use manifold gauges rated for R-410A (800 psi/250 psi low).

4.R-410A is a binary blend of HFC-32 and HFC-125.

5.R-410A is nearly azeotropic - similar to R-22 and R-12. Although nearly azeotropic, charge with liquid refrigerant.

6.R-410A operates at 40-70% higher pressure than R-22, and systems designed for R-22 cannot withstand this higher pressure.

7.R-410A has an ozone depletion potential of zero, but must be reclaimed due to its global warming potential.

8.R-410A compressors use Polyol Ester oil.

9.Polyol Ester oil is hygroscopic; it will rapidly absorb moisture and strongly hold this moisture in the oil.

10.A liquid line dryer must be used - even a deep vacuum will not separate moisture from the oil.

11.Limit atmospheric exposure to 15 minutes -

MAXIMUM.

12.If compressor removal is necessary, always plug compressor immediately after removal. Purge with small amount of nitrogen when inserting plugs.

Manual

2100-455A

Page

16 of 25

Image 16
Contents Installation Instructions Wall Mounted Package Heat Pumps Contents Getting Other Information and Publications For More INFORMATION, Contact These PublishersHeat Pump Wall Mount Model Nomenclature Wall Mount General InformationElectric Heat Table CH3S1 Unit Dimensions CH4S1 and CH5S1 Unit Dimensions Electrical Specifications Single Circuit Dual CircuitShipping Damage GeneralDuct Work FiltersWall Mounting Information Installation InstructionsMounting the Unit CH3S1 Wall Mounting Instructions 6XSSO\2SHQLQJ Electric Heat Clearance Wall Mounting Instructions OpeningFalse Wall Installation Ducted Supply Return At Unit Common Wall Mounting InstallationsWiring Main Power Wiring LOW Voltage WiringThermostat Wire Size TAP RangeStart UP LOW Voltage ConnectionsApplication LOW Voltage Connections For DDC ControlStart UP CONT’D Phase Monitor Service HintsSequence of Operation Compressor Current & Pressure Control ModuleDefrost Cycle Defrost Control BoardSolid State Heat Pump Control Troubleshooting Procedure TroubleshootingTroubleshooting Checking Temperature Sensor Outside Unit Circuit Temperature F VS Resistance R of TemperatureFAN Blade Setting Dimensions FAN Blade Setting FAN Blade DimensionCompressor Solenoid Removal of FAN ShroudIndoor Blower Performance Refrigerant Charge Subcooling LevelMaximum ESP of Operation Pressure Table High Capacity CoolingPressure Table
Related manuals
Manual 28 pages 36.1 Kb Manual 14 pages 10.23 Kb

CH3S1, CH5S1, CH4S1 specifications

Bard CH3S1, CH4S1, and CH5S1 represent a formidable trio of advanced technologies in the field of AI-driven natural language processing. These models are designed to facilitate seamless communication, enhance productivity, and deliver personalized experiences across various applications.

One of the main features of the Bard CH series is its ability to understand and generate human-like text. This is achieved through deep learning algorithms that analyze vast datasets to learn language patterns, context, and nuances. The CH3S1 model, for instance, excels in basic conversational tasks, making it suitable for customer support, virtual assistants, and simple content generation. Its training allows it to respond efficiently to user inputs while maintaining clarity and engagement.

As we progress to the CH4S1 model, we observe significant enhancements in contextual understanding. This model can handle more complex conversations, making it adept at tasks requiring greater cognitive processing, such as technical support and nuanced dialogue-based applications. The increased parameter count and refined training methods contribute to its ability to grasp intricate sentence structures and varied linguistic styles, leading to more coherent and relevant responses.

Building upon the capabilities of its predecessors, the CH5S1 model represents the pinnacle of the Bard CH series. It integrates advanced features such as multi-modal processing, allowing it to work with text, images, and even sound. This model is engineered to perform in more specialized fields, such as healthcare, legal, and creative writing, where precise language and context are critical. The CH5S1 leverages feedback loops from real-time interactions to continuously improve its understanding and output, making it not only a tool for communication but also an intelligent partner for businesses and individuals alike.

In terms of technology, all three models utilize transformer architecture, which has proven effective in tasks requiring attention and context retention. They also implement reinforcement learning techniques to adapt and refine their models based on user engagement data. Furthermore, security and data privacy are prioritized, with strict adherence to ethical AI guidelines to ensure user trust.

Overall, the Bard CH series signifies a leap forward in artificial intelligence, combining advanced linguistic capabilities with a user-centric approach, thus redefining how we interact with machines and enhancing our digital experiences.