Parkside PBS 600 A1 manual Technical information, Workplace safety, Electrical safety

Page 6

Introduction / General safety advice for electrical power tools

1 Vacuum extraction adapter and reducer piece (for external vacuum extraction)

2 Clamps

1 Operating instructions

Technical information

Belt sander:

Parkside PBS 600 A1

Nominal voltage:

230 V~ 50 Hz

Nom. power input:

600 W

No-load belt speed:

170 - 250 m / min

Sanding belt:

75 x 457 mm

Protection class:

II /

Noise and vibration data:

Measured values for noise are determined in accor- dance with EN 60745. The A-weighted noise level of the electrical power tool are typically:

Sound pressure level:

89 dB(A)

Sound power level:

100 dB(A)

Uncertainty K:

3 dB

Wear ear protection!

Total vibration, EN 60745:

Vibration emission value ah,D = 2,5 m / s2 Uncertainty K = 1.5 m / s2

WARNING! The vibration level given in these instructions has been measured in accordance with a standardised measurement procedure specified in EN 60745 and can be used to compare devices. Different uses of the device give rise to different vi- bration levels and in many cases they may exceed the values given in these instructions. It is easy to underestimate the vibration load if the electrical power tool is used regularly in particular circumstances.

Note: If you wish to make an accurate assessment of the vibration loads experienced during a particu- lar period of working, you should also take into account the intervening periods of time when the device is switched off or is running but is not actual- ly in use. This can result in a much lower vibration load over the whole of the period of working.

General safety advice for electrical power tools

WARNING! Read all the safety advice and instructions! Failure to observe the safety advice and instructions may result in electric shock, fire and / or serious injury.

KEEP ALL THE SAFETY ADVICE AND INSTRUC- TIONS IN A SAFE PLACE FOR FUTURE REFER- ENCE! THE TERM “ELECTRICAL TOOL” USED IN THE SAFETY ADVICE REFERS TO ELECTRICAL TOOLS POWERED BY MAINS ELECTRICITY (BY MEANS OF A MAINS LEAD) AND ELECTRICAL TOOLS POWERED BY RECHARGEABLE BATTER- IES (WITHOUT A MAINS LEAD).

1. Workplace safety

a)Keep your working area clean and well lit. Untidy or poorly lit working areas can lead to accidents.

b)Do not work with the device

in potentially explosive envi- ronments in which there are

inflammable liquids, gases or dusts. Electrical power tools create sparks, which can ignite dusts or fumes.

c)Keep children and other peo-

ple away while you are op- erating the electrical tool.

Distractions can cause you to lose control of the device.

2. Electrical safety

To avoid danger to life from electric shock:

a)The mains plug on the device must match the mains socket. The plug must not be modified in any way. Do not use an adapter plug with devices fitted with a protective earth. Unmodified plugs and matching sockets reduce the risk of electric shock.

GB/IE

7

Page 5 Page 7
Image 6
Page 5 Page 7
Contents PBS 600 A1 GB / IE Page Table of contents Belt sander PBS 600 A1 Features and equipmentIntroduction Proper useWorkplace safety Electrical safetyTechnical information Careful handling and use of electrical power tools General safety advice for electrical power toolsPersonal safety Do not use the mains lead forSafety advice for belt sanders Wear safety glasses and a dust protection maskTensioning / changing the sanding belt Advice on usePreparing for use Vacuum dust extractionSwitching on and off Preparing for use / OperationSelecting the correct rotational speed and sanding belt Service centre Using the device in a fixed mountingMaintenance and cleaning WarrantyWarranty / Disposal DisposalDeclaration of Conformity / Manufacturer Allgemeine Sicherheitshinweise für Elektrowerkzeuge InhaltsverzeichnisEinleitung InbetriebnahmeAusstattung EinleitungBandschleifer PBS 600 A1 Einleitung Bestimmungsgemäßer GebrauchLieferumfang Technische DatenArbeitsplatz-Sicherheit Allgemeine Sicherheitshinweise für Elektrowerkzeuge Elektrische Sicherheit Sicherheit von PersonenVermeiden Sie Lebensgefahr durch elektrischen Schlag Verwendung und Behandlung des Elektrowerkzeugs Sicherheitshinweise für BandschleiferTragen Sie Schutzbrille und Staub- schutzmaske Schleifband einspannen / wechseln ArbeitshinweiseEin- und ausschalten Inbetriebnahme / BedienungStaubabsaugung Drehzahl und Schleifband wählenTipps und Tricks Bedienung / Wartung und ReinigungStationäres Arbeiten Wartung und ReinigungGarantie Wartung und Reinigung / Service / Garantie / EntsorgungService EntsorgungKonformitätserklörung / Hersteller Konformitätserklärung HerstellerKompernass Gmbh

PBS 600 A1 specifications

The Parkside PBS 600 A1 is a versatile and efficient belt sander designed for both amateur woodworkers and DIY enthusiasts. This powerful tool is an integral addition to any workshop, providing an optimal solution for sanding surfaces quickly and effectively.

One of the standout features of the PBS 600 A1 is its robust 600-watt motor, which delivers sufficient power to tackle a variety of projects. It operates at a maximum speed of 380 meters per minute, ensuring that users can complete their sanding tasks with speed and precision. This makes the sander ideal for removing paint, smoothing surfaces, or preparing wood for finishing.

The belt sander is equipped with a 75 x 457 mm sanding belt, providing a broad surface area for maximum efficiency. The adjustable belt tracking system allows for easy modifications, ensuring that the sanding belt remains aligned properly, which in turn prolongs the lifespan of the belt and enhances overall performance.

Another noteworthy characteristic of the Parkside PBS 600 A1 is its ergonomic design. It features a comfortable, rubberized handle that aids in minimizing user fatigue during extended periods of use. The tool is lightweight, which contributes to its maneuverability and ease of handling, allowing users to reach tight spots and corners without hassle.

Safety is also a priority in the design of the PBS 600 A1. It comes with an integrated dust extraction port that can be connected to a vacuum cleaner, significantly reducing airborne dust and ensuring a cleaner working environment. This feature not only promotes safety but also enhances visibility when working on projects.

Versatility is a key theme with this tool, as it is suitable for various materials, including wood, plastic, and metal. The adjustable speed control allows users to select the optimal speed for different surfaces, making it adaptable to various sanding requirements.

Furthermore, the Parkside PBS 600 A1 is an economically friendly choice, as it combines innovative technology with a budget-friendly price point, making high-quality sanding accessible for all homeowners and hobbyists. Its blend of power, precision, and adaptability makes the PBS 600 A1 an essential tool for achieving professional-quality results in sanding applications.
Top Page Image Contents