Grizzly H6332 owner manual Troubleshooting, Symptom Possible Cause Solution

Page 15

TROUBLESHOOTING

Symptom

Possible Cause

Solution

Air leaking at

1.

O-rings in trigger valve hous-

1.

O-rings must be replaced &

trigger valve

 

ing are damaged.

 

operation of safety nose must

area.

 

 

 

be checked.

 

 

 

 

 

Air leaking

1.

Loose screws in housing.

1.

Tighten screws.

between hous-

2.

Damaged O-ring.

2.

Replace O-ring.

ing and hose.

3.

Loose air fitting.

3.

Tighten air fitting & use teflon

 

 

 

 

tape.

 

 

 

 

 

Air leaking

1.

Damaged seal.

1.

Replace damaged seals.

between hous-

 

 

 

 

ing and cap

 

 

 

 

assembly.

 

 

 

 

 

 

 

 

 

Tool skips nails

1.

Air leaks.

1.

Tighten screws and fittings.

while discharg-

2.

Dirt in nose.

2.

Clean nose.

ing.

3.

Dirt or damage prevents

3.

Clean magazine and inspect/

 

 

nails from moving freely.

 

repair damage.

 

4.

Inadequate air flow to tool.

4.

Check fittings, hose, compres-

 

 

 

 

sor & air pressure.

 

5.

Worn piston O-ring or lack of

5.

Replace O-ring and lubricate.

 

 

lubrication.

 

 

 

6.

Damaged trigger valve O-

6.

Replace trigger valve O-rings.

 

 

rings.

 

 

 

7.

Worn bumper.

7.

Replace bumper.

 

8.

Cap seal leaking.

8.

Replace cap seal.

 

 

 

 

 

Tool runs slowly

1.

Nailer is not lubricated.

1.

Lubricate nailer.

or has a loss of

2.

Broken spring in cap assem-

2.

Replace spring.

power.

 

bly.

 

 

 

3.

Exhaust port in cap is

3.

Clean or replace damaged inter-

 

 

blocked.

 

nal parts.

 

 

 

 

 

Fasteners fre-

1.

Nails are the wrong size.

1.

Use correct nails.

quently jam the

2.

Nails are bent or dirty.

2.

Use undamaged, clean nails.

nailer.

3.

Magazine or nose screws

3.

Tighten magazine.

 

 

are loose.

 

 

 

4.

Driver or driver guide are

4.

Replace worn or damaged

 

 

worn or damaged.

 

parts.

 

5.

Nails are wrong angle.

5.

Use correct angle nails.

 

 

 

Nailer does not

1. Nailer is not lubricated.

1. Follow lubricating instructions.

fire.

2.

Nail is jammed in magazine

2.

Clear nailer magazine or dis-

 

 

or discharge area.

 

charge area.

 

3.

Piston shaft is damaged.

3.

Replace piston shaft.

 

4.

Air pressure too low.

4.

Check/increase air pressure.

 

 

 

 

 

Air blows out

1.

O-ring slipped out of groove

1.

Reinstall/replace suspect O-ring;

of exhaust cap;

 

or damaged inside nailer.

 

turn down the air pressure to

nailer will not

 

 

 

prevent.

fire.

 

 

 

 

 

 

 

 

 

H6332 11⁄4" Brad Nailer

-13-

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Model H6332 11⁄4 Brad Nailer Safety Safety Instructions For Pneumatic ToolsBefore Operating This Equipment H6332 11⁄4 Brad Nailer Additional Safety Instructions for Nailers H6332 11⁄4 Brad Nailer Introduction Foreword Contact InfoMachine Data UnpackingInventory SET UPCompressed Air System Disconnect Nailer from the AIR Supply Safety Nose MechanismOperations LoadingOperating To adjust the depth Adjusting DepthTo clear a jammed nail from the dis- charge area Clearing Jammed NailsReplacing Pistons/O Rings CleaningLubricating Cleaning & LubricationSymptom Possible Cause Solution TroubleshootingH6332 Parts Breakdown Description H6332 Parts ListWarranty and Returns Warranty Card Place Stamp Here

H6332 specifications

The Grizzly H6332 is a versatile and powerful benchtop sander designed for both hobbyists and professionals who require precision and efficiency in their woodworking projects. This robust machine features a combination of sanding capabilities, making it an essential tool for achieving smooth surfaces and refined edges on a variety of materials.

One of the main features of the Grizzly H6332 is its dual sanding capabilities. It comes equipped with both a 1-inch belt sander and a 5-inch disc sander, allowing users to tackle numerous tasks, from shaping and smoothing to finishing and contouring. The belt sander operates at a speed of 1,800 feet per minute, providing ample power to handle even the toughest materials with ease. The disc sander runs at 3,450 RPM, delivering a high-speed sanding experience that results in clean and precise finishes.

Another notable characteristic of the H6332 is its sturdy construction. Built on a solid cast iron base, this sander ensures minimal vibration during operation, promoting accuracy and stability. The heavy-duty design is complemented by a robust motor, typically rated at 1/2 horsepower, which provides the necessary torque for consistent sanding performance.

Additionally, the Grizzly H6332 has a built-in dust collection system that helps maintain a clean workspace by effectively capturing debris generated during sanding. This feature not only contributes to a healthier working environment but also prolongs the life of the sanding belts and discs by minimizing the accumulation of dust and particles.

Ease of use is another significant advantage of the H6332. The adjustable sanding tables can be tilted for bevel sanding, enhancing its versatility for various projects. Furthermore, the machine's compact size makes it suitable for workshops with limited space, and its portable design allows for easy transportation between job sites.

In summary, the Grizzly H6332 is a reliable and efficient benchtop sander that combines powerful sanding capabilities with a durable construction. With its dual sanding options, robust motor, and integrated dust collection, it is an excellent choice for anyone serious about woodworking and looking to achieve professional-quality results. Whether you're an aspiring craftsman or an experienced woodworker, the H6332 is equipped to meet your sanding needs with precision and ease.
Top Page Image Contents