Emerson LK59FOM, LK59FSST warranty Installation Fluorescent Bulbs Glass Shade

11.Position the cup/light fitter(1)(7) on the cover plate(2) and install the three screws(3) that were previously removed in Step 2 and tighten securely.

!WARNING

To avoid possible fire or electric shock, be careful not to pinch wires between switch cup and the cover plate.

12. Proceed to “Installation of Fluorescent Bulbs and Glass Shade” section.

Installation on Emerson Fans Having Two-Piece Die-Cast Switch Housings

1.Remove all parts and parts packages from carton.

!WARNING

To avoid possible electric shock, be sure electricity is turned off at the main fuse or circuit breaker box before wiring.

2.Remove the cover(5) from the fan switch housing(1) by removing the two outer screws(2). (See Figure 4).

3.Remove the center screw(4) from the cover(5). Insert the black and white wires from the light fitter(6) thru the hole and thread the switch housing cover tightly onto the light fitter.

4.Insert the black and white wires through the lockwasher(8) and hex nut(7) supplied. Firmly tighten the hex nut to secure the light fitter to the switch housing cover(5).

(1) SWITCH	FAN SWITCH
	CHAIN
HOUSING

ASSEMBLY	(3) WIRE
BLUE WIRE	CONNECTORS
BLACK WIRE	WHITE WIRES
(5) COVER	(7) HEX NUT
	(8) LOCKWASHER
(4) CENTER
SCREW
(2) SCREWS
	(6) LIGHT FITTER

Figure 4

5.Carefully locate the white and blue wires (labeled either “L” or “LIGHT”) in the switch housing. Remove and retain the wire connectors(3) from the wires.

6.Connect the white wire from the ceiling fan to the white wire of the light fitter(6). Connect the blue wire from the ceiling fan to the black wire of the light fitter. Use U.L. listed wire connectors(3) (previously removed in Step 5) to make connections. (Figures 3 and 4.)

7.Carefully tuck all wires and splices into the switch housing(1).

8.Attach the cover/light fitter(5)(6) to the switch assembly housing(1) using the two outer screws(2) that were removed in Step 2) (Figure 4.)

!WARNING

To avoid fire or electrical shock, be careful not to pinch wires between the switch housing assembly and the cover.

9.Proceed to “Installation of Fluorescent Bulbs and Glass Shade” section.

Installation of

Fluorescent Bulbs and

Glass Shade

!WARNING

To avoid fire hazard, do not exceed wattage indicated on the fixture.

1.Carefully position one of the GU24 fluorescent bulbs(1) (supplied) into the light fitter socket. Twist the bulb clockwise, approximately 1/16 turn, to engage the bulbs pins into the light fitter socket holes(2) (Figure 5). Install the remaining three GU24 fluorescent bulbs in the same manner.

2.Remove the fan switch pendant(3) from the fan switch chain(4) for installation of glass. Place the fan switch chain through the light fitter plate(5) hole (Figure 5).

(1)13-WATT GU24

FLUORESCENT BULB (4)

(2) LIGHT FITTER SOCKET

	LIGHT FITTER
(5) LIGHT FITTER	PLATE
PLATE HOLES	(4) FAN SWITCH
	CHAIN
Figure 5	(3) FAN SWITCH
	PENDANT

3.Place glass shade (1) onto light fitter(2) making sure that both fan switch chain(3) and light fitter chain(4) are positioned through the center hole in glass shade(1) (Figure 6).

4.Slide the switch chain(3) through the side hole of the guide plate(5) and the light fitter chain(4) through the center hole of the guide plate(5) (Figure 6).

5.Slide the guide plate(5) up the light fitter’s threaded nipple until the glass shade(1) mates with the bottom of the light fitter plate (Figure 6).

6.Install the hex nut onto the threaded nipple and firmly hand tighten the nut to secure the guide plate(5) and glass shade(1) onto the light fitter(2).

7.Slide the fan switch chain(3) through the side hole of the glass cap and slide the light fitter chain(4) through the center hole of the glass cap(6). Slide the glass cap(6) up the threaded nipple until it rests against the bottom of the glass shade(1) (Figure 6).

8.Pass the light fitter chain(4) through the center of the finial nut and fasten the finial nut(7) onto the fitter nipple. Gently hand tighten the finial nut(7) up against the bottom of the glass cap(6) to secure it in position (Figure 6).

9.Reinstall the fan switch pendant(8) to the fan switch chain(3) (Figure 6).

	13-WATT GU24
(2) LIGHT FITTER	FLUORESCENT BULB
THREADED	LIGHT FITTER
NIPPLE
	PLATE

	(1) GLASS
	SHADE
(4) LIGHT FITTER	(3) FAN SWITCH
CHAIN	CHAIN
(5) GUIDE PLATE
HEX NUT

(6) GLASS CAP

(7) FINIAL NUT (8) FAN SWITCH PENDANT

(9)LIGHT SWITCH PENDANT/COUPLING

Figure 6

10.Installation is now complete. Turn on the electricity at the main fuse or circuit breaker box.

4 5