RIDGID R2600 manual Specific Safety Rules, Service, Additional Safety Rules

Page 4

GENERAL SAFETY RULES

Service

Tool service must be performed only by qualified repair personnel. Service or maintenance performed by unqualified personnel could result in a risk of injury.

When servicing a tool, use only identical replace- ment parts. Follow instructions in the Maintenance section of this manual. Use of unauthorized parts or failure to follow Maintenance Instructions may create a risk of electric shock or injury.

SPECIFIC SAFETY RULES

￿Hold tool by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring or its cord. Contact with a “live” wire will make exposed metal parts of the tool “live” and shock the operator.

Additional Safety Rules

Know your power tool. Read operator’s manual carefully. Learn its applications and limitations, as well as the specific potential hazards related to this tool. Following this rule will reduce the risk of electric shock, fire, or serious injury.

Always wear safety glasses. Everyday eyeglasses have only impact-resistant lenses; they are NOT safety glasses. Following this rule will reduce the risk of serious personal injury.

Protect your lungs. Wear a face or dust mask if the operation is dusty. Following this rule will reduce the risk of serious personal injury.

Protect your hearing. Wear hearing protection during extended periods of operation. Following this rule will reduce the risk of serious personal injury.

Inspect tool cords periodically and, if damaged, have repaired at your nearest Authorized Service Center. Constantly stay aware of cord location. Following this rule will reduce the risk of electric shock or fire.

Check damaged parts. Before further use of the tool, a guard or other part that is damaged should be carefully checked to determine that it will oper- ate properly and perform its intended function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting, and any other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced by an authorized service center. Following this rule will reduce the risk of shock, fire, or serious injury.

Do not abuse cord. Never carry the tool by the cord or yank it to disconnect it from the receptacle. Keep cord away from heat, oil, and sharp edges. Following this rule will reduce the risk of electric shock or fire.

Make sure your extension cord is in good condi- tion. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. A wire gage size (A.W.G.) of at least 16 is recommended for an extension cord 50 feet or less in length. A cord exceeding 100 feet is not recom- mended. If in doubt, use the next heavier gage. The

smaller the gage number, the heavier the cord. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating.

Inspect for and remove all nails from lumber before using this tool. Following this rule will reduce the risk of serious personal injury.

Drugs, alcohol, medication. Do not operate tool while under the influence of drugs, alcohol, or any medication. Following this rule will reduce the risk of electric shock, fire, or serious personal injury.

Save these instructions. Refer to them frequently and use them to instruct others who may use this tool. If you loan someone this tool, loan them these instructions also.

WARNING:

Some dust created by power sanding, sawing, grind- ing, drilling, and other construction activities contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

lead from lead-based paints,

crystalline silica from bricks and cement and other masonry products, and

arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equip- ment, such as those dust masks that are specially designed to filter out microscopic particles.

4

Image 4
Contents OPERATOR’S Manual Table of Contents IntroductionGeneral Safety Rules Electrical SafetyPersonal Safety Work AreaService Specific Safety RulesAdditional Safety Rules Symbols Symbol Name DESIGNATION/EXPLANATIONSpecifications ElectricalDouble Insulation Electrical ConnectionUnpacking ApplicationsInstructions Packing ListFeatures Features Sanding Disc Selection AssemblyAttaching Hook and Loop Sanding Discs Remove PSA Sanding Disc Before Storage Attaching the Dust Bag Attaching the Sander to a VacuumTurning the Sander On/Off OperationOperating the Sander Emptying the Dust Bag Adjustments Variable Speed SwitchMaintenance Brush ReplacementGeneral Bearing LubricationPage Page Warranty DAY Satisfaction Guarantee PolicyCustomer Service Information