BEA 10MATRIX warranty Programming

7 Programming

I.THE 3 CONFIGURATIONS

A.Configuration A: Single Loop Detector (MATRIX-S)

B.Configuration B: Dual Loop Detector in Independent Mode with Dipswitch #10 OFF (MATRIX-D)

C.Configuration C: Dual Loop Detector in Combined Mode with Dipswitch #10 ON (MATRIX-D)

Dip Switch	Configuration A		Configuration B		Configuration C
	Single loop		Dual loop in independent mode		Dual loop in combined mode
	OFF	ON	OFF	ON	OFF	ON
DS#1	See next table		High (loop A)	Low (loop A)	High (loop A)	Low (loop A)
				[High –30%]		[High –30%]
DS#2			High (loop B)	Low (loop B)	High (loop B)	Low (loop B)
				[High –30%]		[High –30%]
DS#3	Active mode	Passive mode	Active mode	Passive mode	Active mode	Passive mode
DS#4	ASB OFF	ASB ON	ASB OFF	ASB ON	ASB OFF	ASB ON
DS#5	Relay A :	Relay A :	Relay A :	Relay A :	Not used	Not used
	Presence on	Pulse on loop	Presence on loop A	Pulse on loop A
	loop A
DS#6	Relay A :	Relay A :	Relay A :	Relay A :	Relay B :	Relay B:
	Pulse on loop	Pulse on loop A	Pulse on loop A	Pulse on loop A	Non-Directional	Directional A→B
	A	exit	entry	Exit	mode	mode
	entry
DS#7	Relay B :	Relay B :	Relay B :	Relay B :	Relay B :	Relay B :
	Presence on	Pulse on loop A	Presence on loop B	Pulse on loop B	Pulse on loop B	Pulse on loop A
	loop A
DS#8	Relay B :	Relay B :	Relay B :	Relay B :	Relay B :	Relay B :
	Pulse on loop	Pulse on loop A	Pulse on loop B	Pulse on loop B	Pulse on loop entry	Pulse on loop exit
	A	exit	entry	exit
	entry
DS#9	100 ms	500 ms	100 ms	500 ms	100 ms	500 ms
DS#10	Not used	Not used	Independent	Combined mode	Independent	Combined mode

II. POTENTIOMETERS

A Potentiometer for Adjustment of the Maximum Duration of a Presence Detection: from 1 min to Infinity (See PRESENCE TIME)

A Potentiometer for Adjustment of the Linear Sensitivity (Δf) for the Loop A: from 0.005% to 0.5% (See SENSITIVITY)

A Potentiometer for Adjustment of the Linear Sensitivity (Δf) for the Loop B: from 0.005% to 0.5% (See SENSITIVITY)

PRESENCE TIME

1 min 10 min1 hr

MIN

2 hr

MAX

Infinity 20 hr 5 hr

SENSITIVITY

0.5% 0.44%0.34% MIN

0.25%

MAX

0.005% 0.1% 0.18%

III. RELAY CONFIGURATION (DIPSWITCH #3)

A 10 position dip switch is located on the front of the Matrix single detector. Dip switch 3, 5, 6, 7 and 8 configure the relay, while dip switch 9 controls the duration of the pulse when the Matrix is configured for pulse operation, (as opposed to presence). Configurations are as follows:

DIPSWITCH 3:

OFF= FAIL-SECURE MODE Relay is NOT energized when power is applied. Relay is energized upon detection only. In this mode, the NO circuit is open, and the NC circuit is closed. Thus, if a closed circuit is required upon detection, one must use the NO and COM terminals since they would close upon detection. When the Matrix is NOT powered, it is in the same state as it would be for non-detection.

ON = FAIL-SAFE MODE Relay is energized as soon as power is applied and de-energizes upon detection or power loss. In this mode, upon powering the detector, the NO circuit becomes closed, and the NC circuit becomes open. Thus, if a closed circuit is required upon detection, one must use the NC and COM terminals, since they would now be OPEN during non-detection, and would close upon detection. When the Matrix is NOT powered, it is in the same state as it would be for detection.

DETECTION STATUS			FAIL-SECURE MODE (Active Mode)
			(Relay is not energized upon power-on)
			DIPSWITCH 3 = OFF
NO DETECTION			The COM and NO terminals are OPEN.
		COM and NC terminals are CLOSED.
		The relay is de-energized.
DETECTION		The COM and NO terminals are CLOSED.
		COM and NC terminals are OPEN.
	Same
		The relay is energized.
			The COM and NO terminals are OPEN.
UPON POWER LOSS
		COM and NC terminals are CLOSED
		The relay is de-energized.

FAIL-SAFE MODE (Passive Mode)

(Relay becomes energized upon power-on)

DIPSWITCH 3 = ON

The COM and NO terminals are CLOSED. COM and NC terminals are OPEN.

The relay is energized.

The COM and NO terminals are OPEN. COM and NC terminals are CLOSED. The relay is de-energized.

The COM and NO terminals are OPEN. Same COM and NC terminals are CLOSED.

The relay is de-energized.

75.1046.04 EN 20080505 Page 3 of 5