Diamondback manual Installation of DPLS1 Drain Pan Level Sensor/Control

Page 2

DPLS1 Drain Panel Level Sensor/Control Protected under one or more patents

© 2011 Mitsubishi Electric & Electronics USA, Inc.

Type of Harness

Indoor Unit Models

Connector to Indoor Unit Control Board

Connector to Thermistor

Connector to Control Box

 

 

 

 

 

 

M2 Wire

MS

MSZ/Y

2 pin, female connector (with black

2 pin, male connector to:

2 pin, male connector

Harness

MFZ

 

heat shrink) to CN111

RT11 (Room Temp. Thermistor)

 

 

 

 

 

 

 

 

 

PKA

PCA

 

2 pin, male connector to:

 

 

PEA(D)

PLA

2 pin, female connector to CN20

 

 

TH1 (Room Temp. Thermistor)

 

 

SEZ

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SLZ

 

 

2 pin, male connector to:

 

P Wire

PKFY-P**NBMU-E

 

TH1 (Room Temp. Thermistor) or

2 pin, male connector

Harness

 

 

 

PLFY-P**NCMU-E

 

 

 

 

2 pin, female connector to CN20,

TH22 (Pipe Temp.

 

 

 

 

 

 

PMFY-P**NBMU-E

CN21 or CN29

 

 

Thermistor/Liquid) or

 

 

 

 

 

PVFY-P**E00A

 

TH23 (Pipe Temp

 

 

 

 

 

 

 

PEFY-P**NMHU-E

 

Thermistor/Gas)

 

 

 

 

 

 

 

 

PLA

 

 

 

 

 

PKA

 

 

 

 

 

PCA

 

 

4 pin, male connector to

 

 

PEA(D)

 

 

 

 

 

SEZ

 

4 pin, female connector to CN44

TH2 (Pipe Temp.

 

 

PKFY-P**NH/

 

Thermistor/Liquid) and

 

 

 

 

 

 

KMU-E

 

 

 

 

 

PLFY-P**NBMU-E

 

TH5 (Pipe Temp. Thermistor/Gas)

 

 

PCFY-P**NKMU-E

 

 

 

 

PEFY-P**NMS/AU-E

 

 

 

 

 

 

 

 

 

M1 Wire

MS

 

 

4 pin, male connector to

2 pin, male connector

Harness

 

 

RT12 (Coil Temp. Thermistor)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4 pin, male connector to

 

 

 

 

4 pin, female connector to CN112

RT12 (Coil Temp. Thermistor –

 

 

 

 

 

 

 

MSZ/Y

 

Main) and

 

 

 

 

 

RT13 (Coil Temp. Thermistor –

 

 

 

 

 

Sub)

 

 

 

 

 

 

 

 

MFZ

 

4 pin, female connector to CN113

4 pin, male connector to

 

 

 

RT15 (Coil Temp. Thermistor)

 

 

 

 

 

 

 

 

 

 

 

 

INSTALLATION OF DPLS1 Drain Pan Level Sensor/Control:

(To ensure proper performance of product, instructions must be followed.)

1.Disconnect (and lock-out, if required) all power to the Mr. Slim or CITY MULTI Indoor Unit at the Disconnect Switch (if installed) or at the main disconnect panel serving the indoor and/or outdoor unit.

2.Connect DPLS1 Splice Connector to the selected mating Wire Harness Connector – see wiring harness selection above. Connect the Control Box’s Splice C onnector to the mating connector on the Wire Harness (Fig 1).

Fig 1

2

Image 2
Contents Installation Instructions Installation of DPLS1 Drain Pan Level Sensor/Control PCFY-P**NKMU-E PEFY-P**NMS/AU-EPage Page Limited Warranty Battery Installation on the DPLS1Lawrenceville Suwanee Rd Suwanee, GA Tele