Wall Dimmer | Model |
1. INTRODUCTION
Thank you for your purchase of a SkylinkHomeTM lighting receiver, Wall Dimmer, Model
The Wall Dimmer
All wireless signal communications within the SkylinkHomeTM System are based on rolling code technology to ensure highest security is used.
The following items are included in this package:
-Wall Dimmer
-Wire nuts
-User’s Instructions
Wall Dimmer
Wire nuts
2. SETUP
Setup of the Wall Dimmer is simple. Simply replace your existing wall switch by the Wall Dimmer.
CAUTION
3. PROGRAMMING TRANSMITTERS (TC SERIES) / SENSORS
In order to operate the Wall Dimmer remotely with a transmitter or sensor, it must be programmed to the Wall Dimmer. Each module can be operated by up to 8 different transmitters (or 8 different command signals).
There are 3 operating modes with the Wall Dimmer :
1)Regular Mode - When a valid signal is received, it will turn on or off the light, or change the brightness of the light.
2)Flashing Alert Mode - When a valid signal is received, the light will flash for a specific period of time, which is the time defined in the timer duration. This works as an alert indication.
3)Countdown Timer Mode - When a valid signal is received, the light will be on for a specific period of time, 1 minute, 5 minutes, 15 minutes, 30 minutes, or 60 minutes. This is mainly for energy saving.
You can program multiple buttons/transmitters / sensors to the module and different button/transmitter / sensor can activate a different mode.
To program a TC series transmitter into the Wall Switch Dimmer under regular mode, follow the instructions below:
1.Wall Dimmer must be installed and powered properly. Touch the touch pad. The connected light should be on, and the 2 blue LEDs are off.
2.Press and hold the “SET” button for about 3 seconds, until the upper blue LED flashes quickly.
3.You may now release the “SET” button. The blue LED will continue to flash quickly for about 15 seconds.
Installation is required and enclosed instructions must be followed carefully to all steps and notes. If you are uncertain or uncomfortable performing this installation, please consult a qualified electrician. This manual should also be retained for future reference.
1.Turn off power to the circuit that you plan on installing the Wall Dimmer to at the circuit breaker.
WARNING
Failure to turn off power at the circuit breaker can result in electrical shock causing severe or fatal injury.
Note: Lighting Load
The Wall Dimmer is designed to operate incandescent light or dimmable compact fluorescent light with a maximum load of 600W at 120VAC. Light bulbs must be dimmable in order to achieve dimming function.
2. Follow the diagrams below to install the Wall Dimmer with the 2 wires: |
Live, Load. Use the provided wire nuts to connect these wires |
respectively to the existing wires from the wall : Load(Red) to load and |
Live(Black) to live.. |
Operating Mode | Upper LED Indication |
|
|
Regular | Flashes quickly |
|
|
Flashing Alert | Flashes slowly |
|
|
Countdown Timer | Steadily On |
|
|
4. Within 15 seconds, follow steps A) to C).
A). Press the PROG button on the back of the TC transmitter with a sharp object..
B). Press the button on the TC transmitter that you would like to program.
C). Once the transmitter is programmed, the two blue LEDs on the Wall Dimmer flash quickly then stop flashing, indicating you have successfully programmed the trans- mitter to the module. Now the programmed transmitter button is ready to be used for Regular Mode.
“PROG” button
Press the desired button
3. | After all the wires are connected, ensure that all of the wire connectors |
| are attached securely and there should be no exposed copper wiring. |
| Secure the Wall Dimmer with the provided screws. |
4. | Place the air gap switch to off position. |
5. | Turn the circuit breaker back on. |
6. | Place the air gap switch to on position. The two blue LEDs will be on. |
7. | The light connected will be off. The Wall Dimmer is now installed and |
| you can tap the metal touch pad to turn ON/OFF the connected light or |
| to begin programming to learn transmitters into the Wall Dimmer. |
| Air Gap |
Load | Switch |
| |
Red |
|
Live |
|
Black | Touch |
Blue | |
LED | Pad |
| SET |
Grey Antenna | Button |
Do not cut the antenna!
Note:
Antenna ( grey wire)
Put the antenna directly into the dry wall or through a hole of the metal box into the dry wall to get more control distance with a remote.
To program a TC series transmitter into the Wall Switch Dimmer under Flashing Alert Mode, follow the instructions below:
1.Wall Dimmer must be installed and powered properly. Touch the touch pad. The connected light should be on, and the 2 blue LEDs are off.
2.Press and hold the "SET" button for about 9 seconds, until the upper blue LED flashes slowly.
3.You may now release the "SET" button. The blue LED will continue to flash slowly for about 15 seconds.
4.Within 15 seconds, follow steps A to C.
A.Press the PROG button on the back of the TC transmitter with a sharp object.
B.Press the button on the TC transmitter that you would like to program.
C.Once the transmitter is programmed, the two blue LEDs on the Wall Dimmer flash quickly then stop flashing, indicating you have successfully programmed the transmitter to the module. Now the programmed transmitter button is ready to be used for Flashing Alert Mode.
To program a TC series transmitter into the Wall Switch Dimmer under Countdown Timer Mode, follow the instructions below:
1.Wall Dimmer must be installed and powered properly. Touch the touch pad The connected light should be on, and the 2 blue LEDs are off.
2.Press and hold the "SET" button for about 15 seconds, until the upper blue LED will be steadily on.
3.You may now release the "SET" button. The blue LED will continue to be on for about 15 seconds.