General Care, Safety And Storage
General safety rules
a)Check the condition of the tool before use.
b)The user must check the accuracy of the tool after it has been dropped or subjected to other mechanical stresses.
c)Although the tool is designed for the tough conditions of jobsite use, as with other measuring instruments it should be treated with care.
Do not use prisms or mirrored surfaces
Distances can be measured from all stationary targets without a highly reflective surface, i.e. concrete, stone, wood, plastic, paper, etc. The use of prisms or other highly reflective targets is not permissible and, if attempted, may falsify the results.
Calibration Check
It is recommended to occasionally check the calibration of the tool.
1)Select a known measure distance about 1 to 5 meters (3 to 15 ft) that does not change over time.
2.) Measure the distance 10 times. Calculate the mean deviation from the actual distance. The measured mean deviation should be less than the typical accuracy tolerance of ± 1.5 mm (± 1/16 in)
Cleaning and drying
1.Blow dust off the lens.
2.Do not touch the lens with the fingers.
3.Use only a clean, soft cloth for cleaning. If necessary, moisten the cloth slightly with pure alcohol or a little water.
NOTE Do not use any other liquids as these may damage the plastic components.
Storage
The temperature limits for storage of your equipment must be observed, especially in winter / summer.
Remove the tool from its pouch if it has become wet. The tool, its carrying case and accessories should be cleaned and dried (at maximum 40°C). Repack the equipment only once it is completely dry. Check the accuracy of the equipment before it is used after a long period of storage or transportation.
Transport
Use the original packaging or packaging of equivalent quality for transporting or shipping your equipment.
CAUTION
Always remove the batteries before shipping the tool.
Trouble Shooting
Fault | Possible cause | Remedy | |
|
|
| |
The unit can’t be switched on. | The batteries are exhausted. | Replace the batteries. | |
| Incorrect battery polarity. | Insert the batteries correctly and close the battery | |
|
| compartment cover. | |
| The button is faulty. | Contact Service | |
No distances displayed by the unit. | Measure Button was not pressed. | Press the Measure Button. | |
| Unit was not switched on | Press the Measure Button. | |
| Faulty display. | Contact Service | |
Frequent error messages or the unit doesn’t | The target surface is too brightly lit by the sun. | Measure from the other direction – sun from behind. | |
measure. |
|
| |
The target surface is too shiny. | Take measurements from less shiny surfaces. | ||
| |||
| The target surface is too dark. | Use a lighter colored surface | |
| Bright sunlight towards the tool. | Shade the unit. | |
Temperature indicator - symbol in the display | Temperature too high (>+50 °C / 122 °F) | Allow the unit to cool down. | |
| Temperature too low | Allow the unit to warm up. | |
Unfavorable signal conditions - symbol in the | Insufficient reflected laser light. | Observe the minimum measuring distance (>200 | |
display |
| mm / 8 inch from the front edge of the unit); | |
|
| clean the lenses; take the measurement from a | |
|
| different surface or use a target plate. | |
General hardware fault - symbol in the display | Hardware fault | Switch the unit off and on again. |
– 9 –
Laser Safety
Use of this product by people other than those trained on this product may result in exposure to hazardous laser light.
•Do not remove warning labels from the unit.
•The QM75 is a Class 2M (635 nm) laser product .
•Never look into the laser beam or direct it to the eyes of other people.
•Always operate the unit in a way that prevents the beam from getting into people‘s eyes.
– 10 –
Warranty
Trimble warrants the Quick Measure QM75 to be free of defects in material and workmanship for a period of 3 years. For the first 2 years, Trimble or its authorized Dealer or Service Center will repair or replace, at its option, any defective part, or the entire product, for which notice has been given during the warranty period. For the 3rd year, an exchange fee may apply. This warranty period is in effect from the date the system is delivered by Trimble or its authorized Dealer to the purchaser, or is put into service by a Dealer as a demonstrator or rental component.
Any evidence of negligent or abnormal use, or any attempt to repair equipment by other than
The foregoing states the entire liability of Trimble regarding the purchase and use of its equipment. Trimble will not be held responsible for any consequential loss or damage of any kind.
This warranty is in lieu of all other warranties, except as set forth above, including an implied warranty. Merchantability of fitness for a particular purpose is hereby disclaimed.
Customers should send products to the nearest authorized Factory, Dealer or Service Center for warranty repairs, freight prepaid. In countries with Trimble Service Subsidiary Centers, the repaired products will be returned to the customer, freight prepaid.
– 11 –
Service Request
To locate your local dealer or authorized Trimble Service Center outside the U.S.A for service, accessories, or spare parts, contact one of our offices listed below.
|
| |
Trimble / Spectra Precision Division | Trimble Navigation Singapore PTE Ltd. | |
8261 State Route 235 | 80 Marine Parade Road, | |
Dayton, Ohio | Parkway Parade | |
U.S.A. | Singapore, 449269 | |
(888) | +65 6348 2212 Phone | |
(Toll Free in U.S.A.) | +65 6348 2232 Fax | |
China | ||
Trimble Beijing | ||
www.trimble.com/spectra | ||
Room | ||
| ||
Europe | No. 168 Xiwai Street | |
Trimble Kaiserslautern GmbH | Haidian District | |
Am Sportplatz 5 | Beijing, China 100044 | |
67661 Kaiserslautern | +86 10 8857 7575 Phone | |
GERMANY | +86 10 8857 7161 Fax | |
Tel | www.trimble.com.cn | |
Fax |
| |
Africa & Middle East |
| |
Trimble Export |
| |
P.O. Box 17760 |
| |
JAFZ View, Dubai |
| |
UAE |
| |
| ||
|
– 12 –
Declarations
We declare, on our sole responsibility, that this product complies with the following directives and standards:
EN
Type: QM75
Notice to Our European Union Customers
For product recycling instructions and more information, please go to: www.trimble.com/environment/summary.html
Recycling in Europe
To recycle Trimble WEEE, call: +31 497 53 2430, and ask for the “WEEE associate,” or
mail a request for recycling instructions to: Trimble Europe BV
c/o Menlo Worldwide Logistics Meerheide 45
5521 DZ Eersel, NL
N324
© 2012, Trimble Navigation Limited. All rights reserved. Reorder PN
– 13 – | – 14 – | – 15 – |