Epson 36-714 Additional Specific Safety Rules, Cutting the Workpiece Without the USE

Page 5

ADDITIONAL SPECIFIC SAFETY RULES

FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS PERSONAL INJURY.

1. DO NOT OPERATE THIS MACHINE until it is assembled and installed according to the instructions.

2.OBTAIN ADVICE FROM YOUR SUPERVISOR, instructor, or another qualified person if you are not familiar with the operation of this machine.

3.FOLLOW ALL WIRING CODES and recommended electrical connections.

4.ALWAYS USE GUARDS, SPLITTER, AND ANTI- KICKBACK FINGERS whenever possible. Check to see that they are in place, secured, and working correctly.

5.KICKBACK IS THE NATURAL TENDENCY OF THE WORKPIECE TO BE THROWN BACK AT THE OPERATOR when the workpiece initially contacts the blade or if the workpiece pinches the blade. Kickback is dangerous and can result in serious injury.

AVOID KICKBACK by:

A.keeping blade sharp and free of rust and pitch.

B.keeping rip fence parallel to the saw blade.

C.using saw blade guard and spreader for every possible operation, including all through sawing.

D.pushing the workpiece past the saw blade prior to release.

E.never ripping a workpiece that is twisted or warped, or does not have a straight edge to guide along the fence.

F.using featherboards when the anti-kickback device cannot be used.

G.never sawing a large workpiece that cannot be controlled.

H.never using the fence as a guide when crosscutting.

I.never sawing a workpiece with loose knots or other flaws.

7.REMOVE CUT-OFF PIECES AND SCRAPS from the table before starting the saw. The vibration of the machine may cause them to move into the saw blade and be thrown out. After cutting, turn the machine off. After the blade has come to a complete stop, remove all debris.

8.NEVER START THE MACHINE with the workpiece against the blade.

9.NEVER run the workpiece between the fence and a moulding cutterhead.

10.CUTTING THE WORKPIECE WITHOUT THE USE OF

A FENCE OR MITER GAUGE IS KNOWN AS “FREEHAND” CUTTING. NEVER perform “free-hand” operations. Use either the fence or miter gauge to position and guide the workpiece.

11.HOLD THE WORKPIECE FIRMLY against the miter gauge or fence.

12.CUTTING COMPLETELY THROUGH THE WORK- PIECE IS KNOWN AS “THROUGH-SAWING”. Ripping and cross-cutting are through-sawing operations. Cutting with the grain (or down the length of the workpiece) is ripping. Cutting across the grain (or across the workpiece) is cross-cutting. Use a fence or fence system for ripping. DO NOT use a fence or fence system for cross-cutting. Instead, use a miter gauge. USE PUSH STICK(S) for ripping a narrow workpiece.

13.AVOID AWKWARD OPERATIONS AND HAND POSITIONS where a sudden slip could cause a hand to move into the blade.

14.KEEP ARMS, HANDS, AND FINGERS away from the blade.

15.NEVER have any part of your body in line with the path of the saw blade.

16.NEVER REACH AROUND or over the saw blade.

17.NEVER attempt to free a stalled saw blade without first turning the machine “OFF”.

18.PROPERLY SUPPORT LONG OR WIDE workpieces.

19.NEVER PERFORM LAYOUT, assembly or set-up work on the table/work area when the machine is running.

20.TURN THE MACHINE “OFF” AND DISCONNECT THE MACHINE from the power source before installing or removing accessories, before adjusting or changing set-ups, or when making repairs.

21.TURN THE MACHINE “OFF”, disconnect the machine from the power source, and clean the table/work area before leaving the machine. LOCK THE SWITCH IN THE “OFF” POSITION to prevent unauthorized use.

22.ADDITIONAL INFORMATION regarding the safe and proper operation of power tools (i.e. a safety video) is available from the Power Tool Institute, 1300 Sumner Avenue, Cleveland, OH 44115-2851 (www.powertoolinstitute.com). Information is also available from the National Safety Council, 1121 Spring Lake Drive, Itasca, IL 60143-3201. Please refer to the American National Standards Institute ANSI 01.1 Safety Requirements for Woodworking Machines and the U.S. Department of Labor OSHA 1910.213 Regulations.

SAVE THESE INSTRUCTIONS.

Refer to them often

and use them to instruct others.

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Delta 10 Hybrid Saw Important Safety Instructions Table of ContentsCalifornia Proposition Safety Guidelines DefinitionsImportant Safety Instructions General Safety RulesCutting the Workpiece Without the USE Additional Specific Safety RulesGrounding Instructions Power ConnectionsMotor Specifications Extension Cords Volt Single Phase OperationFunctional Description Carton ContentsAssembly Tools Required AssemblyUnpacking and Cleaning Blade Tilting and Raising Handwheels Disconnect Machine from Power SourceBolting the SAW to Floor Installing Drive Belt Extension Wings S C O N N E C T M a C H I N E F R O M Power SourceDo not Operate the SAW Without Right Table Wing Installed Installing the Switch Installing Your Fence SystemAssembling Blade Guard and Splitter Assembly If alignment is necessary, loosen the two screws Aligning Splitter with Blade SAW BladeAdjusting Table Insert Installing Table InsertInstalling Tool Holders Installing Dust PortOperation Locking Switch in OFF PositionAssembling Miter Gage Starting and Stopping SAWBlade Alignment Checking Blade AlignmentBacklash Adjustments Adjusting Blade AlignmentCommon Sawing Operations Miter Gage Operation and AdjustmentCROSS-CUTTING Never USE the Fence AS a CUT-OFF Gage When CROSS-CUTTINGPush Stick RippingUsing Moulding Cutterhead Using Auxiliary Wood Facing on RIP Fence Using Dado HeadConstructing a Featherboard TroubleshootingPower Tool Institute Constructing a Push Stick PushstickService MaintenanceWarranty AccessoriesPage Page Canadian PORTER-CABLE Delta Service Centers

36-714 specifications

The Epson 36-714 is a robust multi-functional printer that stands out in the competitive landscape of inkjet printing technology. Designed primarily for small to medium-sized businesses, this all-in-one device seamlessly combines printing, scanning, copying, and faxing capabilities into a single compact unit. The 36-714 is particularly known for its high-speed performance and exceptional print quality, making it an ideal choice for professionals looking to boost productivity without sacrificing quality.

One of the defining features of the Epson 36-714 is its advanced PrecisionCore technology. This patented technology enables the printer to deliver sharp, vibrant prints with a resolution of up to 4800 x 2400 DPI. The result is impressive color accuracy and detail, which is especially beneficial for businesses that require high-quality marketing materials, presentations, or detailed documents.

Another key highlight of the 36-714 is its enhanced printing speed. With the ability to print up to 25 pages per minute in black and white and 12 pages per minute in color, this printer minimizes downtime and maximizes efficiency. The device is also equipped with automated duplex printing, allowing users to print on both sides of the paper, which not only saves resources but also reduces paper clutter.

The 36-714 boasts an intuitive 4.3-inch touchscreen interface that simplifies navigation through its various functions. This user-friendly control panel enables quick access to print jobs, scanning options, and settings adjustments, making it easy for users of all skill levels to operate the printer effectively.

In terms of connectivity, the Epson 36-714 offers versatile options, including USB, Ethernet, and wireless capabilities. Users can easily connect the printer to their local network or use mobile printing options through Epson’s iPrint app or Google Cloud Print. This flexibility allows teams to print from multiple devices, whether they are in the office or working remotely.

Security features are also a significant consideration in today’s business environment. The Epson 36-714 addresses this with secure printing options and the ability to set user access controls to safeguard sensitive information.

Moreover, cost-effectiveness is a strong attribute of the Epson 36-714, as it utilizes Epson’s high-capacity ink cartridges. This helps to lower the cost per page, providing more economical printing over time.

In summary, the Epson 36-714 is a versatile, high-performance inkjet printer that excels in speed, quality, and connectivity. Its robust features and thoughtful design make it an essential tool for any business looking to enhance productivity while maintaining exceptional print standards.
Top Page Image Contents