Sears 26462_0 owner manual Use recommended accessories, Never leave tool running unattended

Page 4

18. Use recommended accessories

Consult the owner'smanual for recommended accessories and follow the instructions. The use of

improper accessories may cause hazards. 19. Never stand on tool

Serious injury could occur if the tool is tipped or if the cutting tool is accidentally contacted. DO NOT store materials above or near the tool making it nec- essary to stand on the tool to reach them.

20. Check damaged parts

Before further use of the tool, any guard or other part that is damaged should be carefully checked to ensure that it will operate properly and perform its intended function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting, and any other conditions that may affect its operation. A guard or any other part that is damaged should be properly repaired or replaced.21. Direction of feed

Feed work into a blade or cutter AGAINST the direction of rotation of the blade or cutter only.

1.Always wear eye protection that complies with ANSI Standard Z87.1.

2.Noise levels vary widely with location. To avoid pos- sible hearing damage, wear ear plugs or ear muffs when using your router table for long periods of time.

3.For dusty operations, wear a dust mask along

with safety goggles.

4. Follow the instructions in your router owner'smanual.

5.L_'WARNINGJ Vibrations, caused by the router during use, can cause fasteners to become loose. Before use and periodically during use, check all fasteners to make sure that all are tight and secure.

6.Do not use this product until all assembly and instal- lation steps have been completed. Make sure you have read and understood all safety and

operational instructions in this manual and the router owner'smanual.

7.Make sure that the router bit is properly positioned and clamped in the router before making any cuts.

8.Do not use the router table as a workbench or work

surface. Doing so may damage it, causing it

to be unsafe to use. A workbench should be used for this purpose.

9.This product is designed for cutting flat workpieces. Do not cut or attempt to cut workpieces that are not flat.

10.This product is designed for cutting wood workpieces only. Do not use to cut metal or other non- wood materials.

11.The use of auxiliary in-feed and out-feed

supports is strongly recommended when routing long workpieces. Otherwise those workpieces can cause the router table to tip over.

22. Never leave tool running unattended

Turn power OFF. DO NOT leave tool until it comes to a complete stop.

23.Keep hands away from cutting area

24.Store idle tools

When not in use, tools should be stored in dry, high

or locked-up place - out of reach of children.

25. Do not abuse cord

Keep cord away from heat, oil and sharp edges.

26.Outdoor extension cords

When tool is used outdoors, use only extension cords suitable for use outdoors and so marked.

27.Never use in an explosive atmosphere Normal sparking of the motor could ignite fumes, flammable liquids, or combustible items.

28.Drugs, alcohol, medication

DO NOT operate tool while under the influence of drugs, alcohol, or any medication.

Read and Understand this instruction book completely BEFORE using this product.

12.Keep hands clear of the router bits and working area.

13.Make and use a push stick to move small workpieces across the cutting area.

14.Clean the router after use. The use of a wet/dry vac or vacuum equipment is recommended.

15.Always make sure that work surface of the router table is clean and free from dust, chips, and foreign particles that can interfere with the cut you are going to make. The use of a wet/dry vac or vacuum equipment is recommended.

16.Check the function of the guard before each use.

Remove all dust, chips, and any other foreign parti- cles that can affect its function.

17.'_WARNINGI Never put your fingers under the overhead guard when the router is plugged into an electrical outlet or when the router bit is rotating.

18.Always use the fence to guide the workpiece.

19.Always feed the workpiece AGAINST the rotation of the cutter or router bit.

20.Router bits are extremely sharp; be extra careful when handling and using them.

21.Make sure that the router bits being used are sharp or have been properly resharpened. This will permit fast, efficient, and SAFE routing.

22.Some routers, when positioned in an upside down position (such as on a router table), will drop

or fall out of the router base when the base clamp is loosened to adjust height or depth of cut. Therefore, it is extremely important to support the router from below when making these adjustments or whenever the base clamp is loosened.

23.Always look under the router table at the router

Page 3 Page 5
Image 4
Page 3 Page 5
Contents SF./SCRAFTSMANo Selecting Installing Router Table Inserts End Cutting Using Fence With Push Block RoutingMounting FencePreventing Equipment Make workshop child-proofNever leave tool running unattended Use recommended accessoriesOutdoor extension cords Page Tools Required Router TableMounting Router to the Router Table Before Mounting Craftsman Routers with Three-Hole and 6 Diameter Base PlatesFence Assembly Attachment of the Fence Assembly to Router TableOther Brands of Routers Attaching or removing fence from tableJwarningj Push Block AssemblyAttachment of the Overhead Guard to Push Block Assembly to the Router Table Fence Miter Gauge AssemblyDust Collecting Attachment Mounting Router Table to a Workbench or Work SurfaceSelecting and Installing the Router Table Inserts Alternate MethodGeneral Switch BOX OperationElectrical Requirements To operate the switch box, proceed as follows Router and Switch BOX OperationsAdjusting Depth and Height of CUT Alignment of Unitized Fence to Miter BAR SlotOverhead Guard to Operating Position To Miter BAR SlotEdge Cutting with NON-PILOTED Router Bits Section Adjusting Depth and Height OftheEdge Cutting with Piloted Router Bits END Cutting Using the Fence with the Push Block GROOVING, FLUTING, and VeiningOuan\ To the Router Table Unitized FenceRouting Using the Miter Gauge Ment of Unitized Fence to Miter BAR Slot@ @ @ @ @@@ @ @@@ @ @@ Table Assembly Fence Assembly Miscellaneous Parts Miterbarassembly

26462_0 specifications

Sears 26462_0 is a notable product designed to meet the needs of a diverse range of consumers, offering a blend of functionality, style, and performance. One of the standout features of this model is its sleek and modern design, making it an attractive addition to any home or workspace. The aesthetic appeal is complemented by a sturdy construction that ensures durability, providing users with a reliable product that will stand the test of time.

The 26462_0 is equipped with advanced technologies that enhance its usability. One such technology is its energy-efficient operation, which allows users to reduce their energy consumption while still enjoying optimal performance. This feature not only helps in lowering electricity bills but also contributes to environmental sustainability, making it an appealing choice for eco-conscious consumers.

Another key characteristic of the Sears 26462_0 is its user-friendly interface. The controls are intuitive and accessible, allowing users to quickly familiarize themselves with the product and maximize its features. Additionally, its compact design makes it suitable for small spaces, further increasing its versatility.

Performance-wise, the 26462_0 excels in delivering consistent results. Whether it’s related to its primary function or supplementary features, users can expect reliable performance that meets or exceeds expectations. This model's robust engineering ensures that it can handle a variety of tasks efficiently, catering to both light and heavy-duty requirements.

In terms of maintenance, the Sears 26462_0 has been designed with ease of care in mind. Its materials are easy to clean, and the components are accessible for repairs if necessary. This practicality contributes to a lower total cost of ownership, as users can manage and maintain their product without costly interventions.

Overall, the Sears 26462_0 is a well-rounded choice for anyone in the market for a dependable and stylish addition to their home or office. Its blend of modern design, user-friendly features, energy efficiency, and durable construction positions it as a product that truly meets the evolving needs of today’s consumers. With its solid performance and practical characteristics, the 26462_0 emerges as a commendable option for those seeking quality and reliability in a singular offering.
Top Page Image Contents