Sears 921.16471 owner manual Installation & Assembly, Getting Started, Break In Procedures

Page 6

Installation & Assembly

The air compressor should be turned off, unplugged from the power source, the air bled from the tank and the unit allowed time to cool before any maintenance is performed, Personal injuries could occur from moving parts, electrical sources, compressed air or hot surfaces, The quick connect assembly must be attached before use, Failure to assemble correctly could result in leaks and possible injury, If unsure of assembly instructions or you experience difficulty in the assembly please call your local service department for further information,

Getting Started -

Location of the Air Compressor

The air compressor should always be located in a clean, dry and well ventilated environment. The unit should have at minimum, 12 inches of space on each side. The air filter intake should be free of any debris or obstructions. Check the air filter on a daily basis to make sure it is clean and in working order.

_fdAVlhV[€

Risk Of Fire Or Explosion

This product incorporates snap action switch contacts and a universal electric motor which

tend to produce arcs and sparking and therefore should not be exposed to flammable liquids or vapors. This product is not intended for instal- lation or use in a commercial garage or shop environment.

Grounding Instructions

This product must be grounded. In the event of an electrical short circuit, grounding reduces the risk of electric shock by providing an escape wire for the electric current. This product is equipped with a cord having a grounding wire with an ap- propriate grounding plug. (See the figure below.) The plug must be plugged into an outlet that is

properly installed and grounded in accordance with all local codes and ordinances. Check with

a qualified electrician or service personnel if these instructions are not completely understood or if in doubt as to whether the tool is properly grounded.

Plug

Grounded

Outlet

Grounding Pin

_l_fdAVlhV[e

Improper installation of the grounding plug will result in a risk of electric shock, If repair or replace- ment of the cord or plug is necessary, do not connect the grounding wire to either flat blade terminal, The wire with insulation having an outer surface that is green with or without yellow stripes is the grounding wire, Check with a qualified electrician or serviceman if the grounding instructions are not completely understood, or if in doubt as to whether the product is properly grounded, Do not modify the plug provided; if it will not fit the outlet, have the proper outlet installed by a qualified electrician,

This product is for use on a circuit having a nominal rating of 120 volts and is factory-equipped with a specific electric cord and plug to permit connection to a proper electric circuit. Make sure that the product is connected to an outlet having the same configuration as the plug. No adapter should be used with this product. If the product must be reconnected for use on a different type of electric circuit, qualified service personnel should make the reconnection.

Extension Cords

Use only a 3-wire extension cord that has a 3-blade grounding plug, and a 3-slot receptacle that will accept the plug on the product. Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. Cords must not exceed 25 feet and No. 12 AWG size must be used. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating.

Break In Procedures

No break in procedure is required by the user. This product is factory tested to ensure proper opera- tion and performance.

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents ICRRFT$14RN Gallon Oil-Free, Direct Drive Model NoContents Risk of Movinl Parts Risk of Burns Safety InstructionsImportant Safety Instructions and Guidelines Risk of FallingDuty SpecificationsGlossary CycleParts & Features Installation & Assembly Break In ProceduresGetting Started Operating Procedures Daily Start-Up ProceduresMaintenance StorageTroubleshooting Guide FIrl,fdAVlIAV€Craftsman Air Compressor Model Exploded View Craftsman Air Compressor Model Exploded View Craftsman Air Compressor Model Parts List IRe. I PartI Desc,,ption Ref I Kit I Part DescriptionPage Litros PiPDe impulsi6n directa, Sin aceite # de Modelo Contenido Riesgo por partes en movimiento Instrucciones de seguridadInstrucciones y pautas de seguridad importantes Rieslo de caidaCiclo de trabajo EspecificacionesGlosario Riesgo para la respiraci6n Riesgo de descargas ElectricasDe salida Partes y caracteristicasWlvula de seguridad ReguladorInstalacion y ensamblaje Primer paso Ubicacion del compresor del aireRiesgo de incendio o explosion Procedimientos de operaci6n Procedimiento diario de arranqueMantenimiento AlmacenamientoDiagnostico y correccion de fallas Problema Posible CorreccionCompresor de aire Modelo Vista esquematicaCompresor de aire Modelo Vista esquematica Lista Las piezas CompresorDe aire Modelo 921.164710#de Descripcion de Parte DescripciOnparte I cantYour Home Our Home

921.16471 specifications

The Sears 921.16471 is a notable example of compact appliances that have made a significant impact in the realm of home convenience. Designed with the modern homeowner in mind, this appliance combines functionality, efficiency, and user-friendly features to cater to various household needs.

One of the main features of the Sears 921.16471 is its impressive versatility. This appliance is designed to perform multiple functions, making it suitable for a wide range of tasks. Whether it’s cooking, baking, or preparing beverages, this model delivers reliable performance across the board. For those seeking to simplify their kitchen experience, the ability to handle various cooking techniques in one machine is a game changer.

Additionally, the Sears 921.16471 incorporates advanced technologies that enhance its usability and efficiency. With intuitive controls and preset cooking programs, users can navigate through its functions with ease. The digital interface allows for precise temperature and time settings, ensuring that every dish is cooked to perfection. Furthermore, the appliance often features a timer function, which adds an extra layer of convenience for busy individuals who need to multitask.

Another standout characteristic is its energy efficiency. The Sears 921.16471 is designed to minimize power consumption, making it an environmentally friendly option that also helps in reducing utility costs. This focus on energy-saving technologies does not compromise performance, as the appliance still delivers powerful results in a fraction of the time compared to traditional cooking methods.

The compact design of the Sears 921.16471 makes it an excellent choice for smaller kitchens or for anyone looking to save counter space. Its sleek design allows it to blend seamlessly into a variety of kitchen aesthetics, appealing to a wide audience. Portable and lightweight, it can be easily stored when not in use.

In summary, the Sears 921.16471 is a versatile and efficient appliance that reflects the needs of today’s consumers. With its multifaceted capabilities, advanced technology, energy-saving features, and space-saving design, it stands as an ideal solution for those looking to elevate their cooking experience while maintaining functionality and convenience in the kitchen. Whether for a quick meal or elaborate cooking sessions, this appliance is equipped to meet diverse culinary needs with ease.
Top Page Image Contents