Lincoln Electric CV-300 manual Safety, California Proposition 65 Warnings

Page 2

i

SAFETY

i

WARNING

CALIFORNIA PROPOSITION 65 WARNINGS

Diesel engine exhaust and some of its constituents are known to the State of California to cause can- cer, birth defects, and other reproductive harm.

The Above For Diesel Engines

The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm.

The Above For Gasoline Engines

ARC WELDING CAN BE HAZARDOUS. PROTECT YOURSELF AND OTHERS FROM POSSIBLE SERIOUS INJURY OR DEATH. KEEP CHILDREN AWAY. PACEMAKER WEARERS SHOULD CONSULT WITH THEIR DOCTOR BEFORE OPERATING.

Read and understand the following safety highlights. For additional safety information, it is strongly recommended that you purchase a copy of “Safety in Welding & Cutting - ANSI Standard Z49.1” from the American Welding Society, P.O. Box 351040, Miami, Florida 33135 or CSA Standard W117.2-1974. A Free copy of “Arc Welding Safety” booklet E205 is available from the Lincoln Electric Company, 22801 St. Clair Avenue, Cleveland, Ohio 44117-1199.

BE SURE THAT ALL INSTALLATION, OPERATION, MAINTENANCE AND REPAIR PROCEDURES ARE PERFORMED ONLY BY QUALIFIED INDIVIDUALS.

FOR ENGINE powered equipment.

1.a. Turn the engine off before troubleshooting and maintenance work unless the maintenance work requires it to be running.

____________________________________________________

1.b.Operate engines in open, well-ventilated areas or vent the engine exhaust fumes

outdoors.

____________________________________________________

1.c. Do not add the fuel near an open flame welding arc or when the engine is running.

Stop the engine and allow it to cool before refueling to prevent spilled fuel from vaporiz- ing on contact with hot engine parts and igniting. Do not spill fuel when filling tank. If fuel is spilled, wipe it up and do not start engine until fumes have been eliminated.

____________________________________________________

1.d. Keep all equipment safety guards, covers and devices in position and in good repair.Keep hands, hair, clothing and tools away from V-belts, gears, fans and all other moving parts when starting, operating or repairing equipment.

____________________________________________________

1.e. In some cases it may be necessary to remove safety guards to perform required maintenance. Remove guards only when necessary and replace them when the maintenance requiring their removal is complete. Always use the greatest care when working near moving parts.

___________________________________________________

1.f. Do not put your hands near the engine fan. Do not attempt to override the governor or idler by pushing on the throttle control rods while the engine is running.

___________________________________________________

1.g. To prevent accidentally starting gasoline engines while turning the engine or welding generator during maintenance work, disconnect the spark plug wires, distributor cap or magneto wire as appropriate.

1.h. To avoid scalding, do not remove the radiator pressure cap when the engine is hot.

ELECTRIC AND MAGNETIC FIELDS may be dangerous

2.a. Electric current flowing through any conductor causes localized Electric and Magnetic Fields (EMF). Welding current creates EMF fields around welding cables and welding machines

2.b. EMF fields may interfere with some pacemakers, and welders having a pacemaker should consult their physician before welding.

2.c. Exposure to EMF fields in welding may have other health effects which are now not known.

2.d. All welders should use the following procedures in order to minimize exposure to EMF fields from the welding circuit:

2.d.1. Route the electrode and work cables together - Secure them with tape when possible.

2.d.2. Never coil the electrode lead around your body.

2.d.3. Do not place your body between the electrode and work cables. If the electrode cable is on your right side, the work cable should also be on your right side.

2.d.4. Connect the work cable to the workpiece as close as possible to the area being welded.

2.d.5. Do not work next to welding power source.

Mar ‘95

Page 1 Page 3
Image 2
Page 1 Page 3
Contents Idealarc CV-300October Safety California Proposition 65 WarningsElectric Shock can kill Cylinder may explode if damaged Précautions DE Sûreté Sûreté Pour Soudage a L’ArcThank You Table of Contents Installation Technical Specifications Idealarc CV-300Input Connections Safety PrecautionsSelect Suitable Location StackingField Installed Options Output ConnectionsParalleling General Warnings OperationOperating Instructions Power Source Operation Operational Features and ControlsDesign Features General DescriptionControls and Settings Thermal Protection Indication LightIndicates Warning Information Located on Right Case Side Voltage ControlC. Output Connectors Output Panel ConnectionsOverload Protection Auxiliary PowerStarting the Machine Compatible Lincoln Equipment AccessoriesFactory Installed OPTIONS/ACCESSORIES Safety Precautions MaintenanceGeneral Maintenance Machine and Circuit ProtectionTroubleshooting HOW to USE Troubleshooting GuideBUILT-IN Diagnostic Routines and Error Codes Error Code Trouble RemedyMachine Troubleshooting Guide Problems Possible Areas Recommended SymptomsProblems Poor arc characteristics Control PC Board defective Options Troubleshooting Guide Control PC Board Meter PC BoardOutput Voltage Fault Protection OperationOptional K857 Remote Control Check Checking Snubber CircuitWiring Diagram CV-300 60Hz Diagrams CV Power Source to AN LN-7 and K857Adapter Power Source to a K867 / K775 LN-7CV Power Source to AN LN-25 Power Source to AN LN-25 / K444-1 Lincoln Power Source to AN LN-742 WireInstallation Instructions TWIST-MATE Cable Plug Installation Instructions Connection of NON-LINCOLN Wire Feeders Dimension Print CV-300 CV-300 How To Read Shop Drawings Precaucion Warnung

CV-300 specifications

The Lincoln Electric CV-300 is a highly regarded power source designed specifically for wire feed welding applications. This machine combines advanced technology with user-friendly features to meet the demanding needs of professional welders. Known for its reliability, efficiency, and versatility, the CV-300 is suitable for various welding processes, including MIG, flux-cored, and DC TIG welding.

One of the standout features of the CV-300 is its constant voltage design. This ensures a stable arc throughout the welding process, which is critical for achieving high-quality welds. The ability to maintain a consistent arc helps in reducing spatter and improves bead appearance, making it ideal for both novice and experienced welders.

The CV-300 is equipped with Lincoln Electric's exclusive Auto-Set technology. This feature simplifies the setup process significantly by allowing users to select the material type and thickness. The machine automatically adjusts the voltage and wire feed speed, ensuring optimal performance without requiring extensive knowledge of welding parameters from the operator.

Another defining characteristic of the CV-300 is its robust construction. Built to endure the rigors of the shop environment, the power source features a durable housing and components that withstand high heat and heavy use. Additionally, it is designed for easy access to internal components, facilitating maintenance and servicing when required.

Portability is another significant advantage of the Lincoln Electric CV-300. Weighing in at a manageable size, the power source can easily be transported to job sites or moved around the workshop, enhancing its usability. It is compatible with various wire feeders, making it an adaptable choice for different welding projects, whether it's light fabrication or heavier industrial work.

The CV-300 also supports a variety of input voltages, making it versatile for use in different settings. Its adaptability allows it to operate efficiently in various environments, ensuring that welders have the power they need at their fingertips.

In summary, the Lincoln Electric CV-300 is a formidable choice for those in need of reliable and powerful welding equipment. With features such as constant voltage output, Auto-Set technology, robust construction, and portability, it meets the demands of modern welding with ease, helping professionals achieve stunning results in their work.
Top Page Image Contents