Grizzly G4000 manual Machine Data Sheet

Page 28

MACHINE DATA

SHEET

Customer Service #: (570) 326-3806 • To Order Call: (800) 523-4777 • Fax #: (800) 438-5901

GRIZZLY MODEL G4000 9" X 19" BENCH LATHE

Design Type	Bench Model
Overall Dimensions:
Overall Length	361⁄2"
Overall Width	22"
Height	15"
Bed Width	41⁄2"
Spindle Bore	3⁄4''
Spindle Taper	# 3 Morse Taper
Tailstock Taper	# 2 Morse Taper
Weight (Net)	250 lbs.
Weight (Shipping)	300 lbs.
Crate Size	41" L x 22" W x 19" H
Footprint	37" x 16"
Construction:	Cast Iron
Capacity:
Swing Over Bed	9''
Swing Over Saddle	5''
Carriage Travel	16"
Max Tool Size	1⁄2'' x 1⁄2''
Distance Between Centers	19''
Lead Screw	9⁄16'' - 16 TPI
Spindle Thread	39 mm X 4 mm
Compound Travel	17⁄8''
Cross Slide Travel	41⁄4''
Tailstock Barrel Travel	19⁄16''
Spindle Speeds	130, 300, 400, 600, 1000, 2000 RPM
Feed Rate Range	18 @ .0023'' - .013''
Thread Range Inch	27 @ 8 TPI - 56 TPI
Thread Range Metric	11 @ .5 - 3.0 mm
Motor:
Type	TEFC Capacitor Start Induction
Horsepower	3⁄4
Phase ⁄ Hertz	Single Phase ⁄ 60Hz
Voltage	110V
Amps	11.6
RPM	1725
Bearings	Shielded And Lubricated For Life
Standard..........................................................................Accessories:	4'' 3-Jaw Chuck w ⁄ Two Sets of Jaws
	4'' 3-Jaw Chuck w ⁄ Two Sets of Jaws
........................................................................	71⁄4''' 4-Jaw Chuck w ⁄ Reversible Jaws
........................................................................................	4-Way Tool Post ⁄ Face Plate
.............................................................................................	Follow Rest ⁄ Steady Rest
.....................................................................................	# 2 Morse Taper Dead Center
.....................................................................................	# 3 Morse Taper Dead Center
........................................................................................	# 2 Morse Taper Live Center
.................................................................................................	Extra C-Type Tool Post
........................................................................................................	Tool Box & Tool Kit

Specifications, while deemed accurate, are not guaranteed.

G4000 9'' x 19'' Lathe

REVISED 5/99

-27-

Image 28

Contents 19 Metal Lathe Table Of Contents Safety Safety Instructions For Power ToolsAMP Rating Additional Safety Instructions For The Lathe 110V Operation Grounding Circuit RequirementsExtension Cords Introduction CommentaryUnpacking Piece InventoryClean Up Site ConsiderationsMountingChucks Assembly & SetupLubrication Live Center See FigureSteady Rest Follow RestControls Spindle SpeedsFeed Rate Feed rates portion of machine plateCarriage Controls Longitudinal handwheelThread Dial Lever Tailstock Controls Single tool holderTest Run Adjustments Spindle RPMTop slide gib adjustment Steady/Follow RestChuck Runout Turning new shoulder on back plate G4000 9 x 19 LatheTailstock Making a dead center G4000 9 x 19 LatheTIP Thread Cutting Example of Gear Set-Up to Cut 10 T.P.lMaintenance Bearing Preload Tailstock oiling pointClosure Machine Data Sheet G4000 9 x 19 Lathe Calculating R.P.M.’s G4000 9 x 19 Lathe Headstock Casting G4000 9 x 19 Lathe Bracket Plate G4000 9 x 19 Lathe Stud Bolt G4000 9 x 19 Lathe Bracket G4000 9 x 19 Lathe Housing G4000 9 x 19 Lathe Gear BOX Casting G4000 9 x 19 Lathe G4000 9 x 19 Lathe Apron Casting PK05M G4000 9 x 19 Lathe Saddle G4000 9 x 19 Lathe Compound Slide Tailstock RAM Rest Casting P40001201 BED Warranty and Returns Warranty Card Grizzly INDUSTRIAL, INC