DeWalt DW788 Scroll Saw Manual & Safety Rules

DW788/383329 8/6/02 10:35 AM Page 2

English

•OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only extension cords intended for use outdoors and so marked.

			Minimum Gage for Cord Sets
Volts		Total Length of Cord in Feet			101-150
120V		0-25	26-50	51-100	101-150
240V		0-50	51-100	101-200	201-300
Ampere Rating			AWG
More	Not more		AWG
Than	Than
0	-	6	18	16	16	14
6	-	10	18	16	14	12
10	-	12	16	16	14	12
12	-	16	14	12	Not Recommended

•WEAR PROPER APPAREL. Do not wear loose clothing, gloves, neckties, rings, bracelets, or other jewelry which may get caught in moving parts. Nonslip footwear is recommended. Wear protective hair covering to contain long hair.

•ALWAYS USE SAFETY GLASSES. Also use face or dust mask it cutting operation is dusty. Everyday eyeglasses only have impact resistant lenses, they are NOT safety glasses.

•DON’T OVERREACH. Keep proper footing and balance at all times.

•MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for best and safest performance. Follow instructions for changing accessories.

•DISCONNECT TOOLS before servicing; when changing accessories, such as blades, bits, cutters, and the like.

•REDUCE THE RISK OF UNINTENTIONAL STARTING. Make sure switch is in off position before plugging in.

•USE RECOMMENDED ACCESSORIES. Consult the instruction manual for recommended accessories. The use of improper accessories may cause risk of injury to persons.

•NEVER STAND ON TOOL. Serious injury could occur if the tool is tipped or if the cutting tool is unintentionally contacted.

•CHECK DAMAGED PARTS. Before further use of the tool, a guard

or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function–check for alignment of moving parts, binding of moving parts, breakage of parts, mounting, and any other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced.

•NEVER LEAVE TOOL RUNNING UNATTENDED. TURN POWER OFF. Don’t leave tool until it comes to a complete stop.

Additional Safety Rules for Scroll Saws

•MATERIAL HOLD-DOWNmust be properly set according to these instructions and remain in position during use.

•NEVER reach under the table when operating or make any adjustments when it is running.

•SECURE saw to work bench or stand with clamps or mounting hardware. Secure work bench or stand to floor.

•DO NOT use the upper arm as a lifting point.

•MAKE SURE blade tension is properly adjusted.

•AVOID awkward hand positions where a sudden slip could cause a hand to move into a saw blade or cutting tool. DO NOT PLACE FINGERS OR HANDS IN PATH OF THE SAW BLADE.

•WHEN REMOVING short workpieces, or cleaning up around the table, be sure the saw is in the OFF position and blade has stopped moving.

•NEVER turn the saw ON before clearing the table of all tools, wood scraps, etc., except the workpiece and related feed or support devices for the operation planned.

•CHECK for proper blade size and type.

•DO NOT attempt to saw stock that does not have a flat surface, unless a suitable support is used.

•HOLD material firmly against table and feed into blade teeth at a moderate speed.

•TURN OFF motor if the material resists being backed out of an uncompleted cut. Use appropriate speed for applications.

•MAKE “relief” cuts before cutting long curves.

DW788 specifications

The DeWalt DW788 is a top-tier scroll saw designed for both professionals and woodworking enthusiasts. Renowned for its durability, precision, and user-friendly features, this tool has gained a loyal following in the woodworking community.

One of the standout features of the DW788 is its powerful 1.3-amp motor. This motor provides ample torque and speed, allowing users to cut through a variety of materials, including hardwood, plywood, and even softer materials like plastic. The saw operates at a variable speed ranging from 400 to 1,750 strokes per minute, enabling precise control over the cutting process for intricate designs and detailed work.

The DW788 is equipped with a dual parallel-link arm system that significantly reduces vibration, ensuring smoother, more accurate cuts. This technology helps maintain the saw’s stability while in use, leading to cleaner edges and reduced strain on the user. Moreover, the arm's design allows for improved visibility of the workpiece, facilitating greater accuracy during cutting.

Another notable characteristic is the saw's blade tensioning system, which makes changing blades fast and easy. Users can quickly and effortlessly switch between different types of blades, such as reverse-tooth blades for a smoother finish or skip-tooth blades for faster cuts. This versatility makes the DW788 an all-around solution for various cutting tasks.

Additionally, the DW788 features a large, tabletop design that provides ample working space for larger projects. The 20 inches of throat capacity means that users can tackle larger pieces of wood without feeling restricted. The onboard dust blower also helps maintain visibility by keeping the cutting line clear of debris, enhancing precision.

Built with user comfort in mind, the DW788 boasts an adjustable saw arm that allows for a 45-degree angle tilt, great for making bevel cuts. The included scroll saw stand and vibration-dampening rubber feet further enhance stability and comfort during cutting sessions.

With its blend of power, precision, and user-friendly features, the DeWalt DW788 scroll saw stands out in the woodworking tool market, making it an excellent choice for anyone looking to invest in a high-quality scroll saw that can handle a wide range of projects.